WED5010LW1 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from North Attleboro, MA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Tumbler drive belt was slipping which made grey dust coat inside of dryer
Installed new belt and cleaned dust and wiped out inside of drum with Fantastic and clean sponge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nelson from Middletown, NY
- Parts Used:
- W10869845
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Washer Would Drain But Not Spin
Removed rear cover (6 screws) unpluged harness from motor control and removed same. Replaced motor control reinstalled harness. Replaced rear cover. Parts used motor control board.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wendy from bush, LA
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer Came On & Made Alot Of Noise
Took off the front of & lifted the top up. Pulled the drum out & replaced the two wheels that turn the drum, replaced the belt & replaced the pully wheel that turns the belt & dryer motor & put back together. The dryer now runs like a new one. Has no noise when running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victoria from Sewell, NJ
- Parts Used:
- 8212450A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I just needed to replace the rack in my dryer
This did not require a "repair", just a replacement. I want to say that the response time and ease of ordering were very good. I would not hesitate to use PartSelect again when needed. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Sayrevlle, NJ
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Drum not rotating
Broken belt, but went with the mainentance kit since it was going to be all apart anyway. Found the job easy to do and the new belt idler was a big improvement over the old style. /also came with instructions. Good for another 5-10 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Jamestown, RI
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Drum stopped turning
Using a stiff putty knife I depressed the clips that hold the top down. I loosened the screws at the lower edge of the front panel and removed the two 5/16 head screws that hold the front on. I unplugged the door switch and lifted the front off the lower screws. I removed the drum and the broken belt. I replaced the rear rollers after applying some dry lube to the shafts and replaced the tension spring and rolled. I replaced the drum and belt and attached the belt to the small pulley on the motor. Then checked the rear gasket felt and reinstalled the front cover and the top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dustin from Martinsville, IN
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Rollers squeaking on dryer
Watched a brief video on YouTube and followed step by step. Real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Bettendorf, IA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The dryer sounded like a herd of buffalos running by.
I needed to replace our drum support rollers - one was completely worn out and wobbling (the buffalo herd noise) the other wasn't too bad, but for an older dryer(15+ years) I figured it was time to replace both wheels. I ordered the maintenance kit that also included the Idler Pulley and drum belt. I spent most of my time with the vacuum since there was a lot of dust accumulated inside the dryer. (I recoverd $1.83 in coins!) The instructions that came with the kit were very helpful for this repair. Plus, there were some online videos that heled as well. Once I had everything apart I noticed the plastic bearing ring on the drum's front was nearly worn out so I quickly ordered this from PartSelect and it arrived quicly in two days - this took only 10 minutes to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Libertyville, IL
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
LOUD squeling from Dryer
Belt was worn, rollers were sticking, idler worn out. Ordered a kit to care for these issues, as usual the reapirs took almost no time. Dryer became a bit quieter for a first load, second load the motor siezed. I priced rebuilding most of the machine and determined replacement was due.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert G from Dansville, NY
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
drum not rotating
Pull lint screen, remove two phillips screws,pry top front up and hinge back,remove two screws at top inside, unplug door switch, lift front and remove, remove drum. Read instructions,install new parts, reverse above dis-assembly, happy dying.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FLOR from Jersey City, NJ
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
broken belt and roller
Replaced Broken Belt and roller
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from N Chelmsford, MA
- Parts Used:
- 4392065
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
drumbelt broken
Used a ropeasround the dyer drum to simulate thebelt to peload the idler This allowed me to get the belt over the motor shaft without the idler sping tenion causing the idler to jump at random timesafer I strted using the rope the belt was on in 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- valerie from mishawaka, IN
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
belt broke
I watched the video online in the order section. then just did it after we received the repair kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Cheswick, PA
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Support Roller Worn Out
Followed instructions supplied ( very easy)
Was this instruction helpful to you?
Thank you for voting!