DDG4580GDL Whirlpool Dryer - Instructions

Replaced both Coils. Purchased M Series coils much less expensive buying coils together instead of seperately. Problem solved.

Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.

I removed the old lint filter and put the new one in! Grateful to find this item for my "antique" dryer.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

loosened two screws on back of top,lifted top away from front panel.it just lifts off front corners,removed two screws at top corners.lift front panel up and out,this panel supports dryer tub,remove slowly,unplug door switch parts are located left side bottom two screws holding in had to have wife hold drum up to put front panel on

Ohmed coils and both had continuity so I changed radiant heat sensor. No bench test for Radiant Heat sensor. Same problem. Changed both coils and dryer works fine. Weak coils were my problem. I read thru the same issues in Parts Select forum and it said Radiant Heat sensor was problem 25% of the time. With coils having continuity and no ohm value specified for coils I made wrong choice but, I have spare parts and look for another 10 years of life in the dryer. Nice to have this forum to research appliance repair. Very helpful for parts location and installation. Dishwasher is next!

Just changed lint trap by removing old one and replacing new one.

I followed the advice posted by other customers. I took the front off the dryer, put the door back in place and ran a cycle. I could see that the igniter was heating properly, but no gas was flowing. Based on what I read I concluded that it was a problem with one of the gas valve coils. It was relatively inexpensive to replace both (and the dry is 10 years old), so I didn't go to the trouble of determining the bad one. I replaced them both. Obviously I unplugged the dryer (no need to turn off gas). There were 2 screws that held the bracket in place which holds the coils. I disconnected the coils, removed the bracket screws, replaced the coils, reattached the bracket screws and reconnected the coils. I then reattached the front plate to the dryer. It was very easy and took about 20 minutes and I had never worked on a dryer before.

Same as others.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit

PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.

First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i decided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.

Simple - took out the defective filter and replaced with the purchased part. The hardest part was figuring out the right lint filter. The extensive info on PART SELECT was very helpful.

It was very easy. Pop out old, connect new wires and done! Can't say enough as to how fast and easy getting the part from this company was. Ordered the part later in the day one night and on the second day the part was there. Outstanding service.

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.

Replaced coils on gas valve.

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!