DBLR333GT0AA Whirlpool Dryer - Instructions

Having recently replaced the heating elements and main bearing on the dryer I knew how to take the thing apart, getting to the motor was easy. However, the fan side of the shaft was longer than the original so I had to bend out the metal front panel where the fan is located so it would spin without grinding against the front of the dryer. That done, the rest was easy to finish, mounting bolts on the motor tightened, one last test before putting it back together and all was well. The dryer now works better than it has for a long time.

Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open). Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.

I removed the door and "flipped" it to open right to left. Rather than remove the existing door latch I added the purchased latch on the right side to enable opening the door right to left or left to right.

Unplugged dryer. Removed screws from top of operating panel. Removed wires from switch. Turned switch 1/4 turn to left and removed. Replaced switch. Turned 1/4 to the right. Re-attached wires. Replaced operating panel and screws. Replaced knob. Plugged in dryer. DONE!!!!!!
Easiest repair ever! Thank you.

I Removed the top cover by removing the two small screws just inside the dryer door at the top. The I removed the dryer front and door assembly by removing the two small screws inside the dryer front on each side. That's it. All the parts can then be accessed and replaced easily. The entire job took 10 minutes including a good cleanout.

Pulled out the remnants of the old latch out with the pliers and then popped the new one in...less than 2 minutes. Oh, and the part was delivered in less than 2 days. Great job, Partselect !

I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with the new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.

Removed the front panel,tiped up the top panel ,removed the drum, drive belt,motor and exaust tube assembly. cleaned and vaccumed all lint from every were. Removed motor from fan blade and houseing. Reinstalled moter and pulley that came with the moter and fan blade. reinstalled all of the rest of the parts and plugedin the wires. once all back together pluged into outlet and turned on and prasto works great.

Inserted handle into slots

Received part in two days.
Removed inspection plate by removing two screws. .Drum bearing was right there. With screwdriver
removed "c" clip, took out what was left of old bearing.
With screwdriver aligned drum, slide new bearing into place. Job was done. Instruction with new part simple and easy to follow.

To perform this repair (please see numerous descriptions on the web for generic belt replacement) I had to rivet two loose parts to the drum in order to reinstall the drum. Specifically, the loose metal disk and hot air shroud at the rear of the drum (near the rear berrings) made it impossible to realign the parts to reinstall the three torx bolts at the rear of the drum during reassembly. These two loose parts are positioned behind the drum (when looking inside the drum) i.e. between the drum and the rear berrings.

It was necessary to align the mounting holes in the drum, disk, and air shroud outside of the dryer itself and then to rivet them in place (making sure the smooth rivet head was INSIDE the drum as to avoid providing a rough edge where the clothes could catch during tumbling). Just press the 3 torx bolts through the holes to establish correct alignment. Be sure to install the rivets ouside of the contact area between the heat shroud and mounting plate. You should see an indented pattern on the heat shroud that you can use as a guide.

It was also helpful to make a black mark on one of the drum mounting holes (inside the drum) and its mate on the berring attachment plate - to help orient you when installing the drum with the 3 torx bolts. It only aligns one way - and making the marks will save you aggravation while your head is in the drum during reassembly. Loud swearing at this point only punishes your ears because, after all, your head is in an acoustically punishing echo chamber - and the echoes make it seem as if the dryer is actually cussing YOU and your incompetence out...

I hope this helps someone else save some time in reinstalling the drum.

One additional pointer: you must remove the lower plate on the rear side of the dryer to wrap the belt around the tensioner pulley and motor drive. The belt wraps, from right to left, first around the motor pulley and then up and to the left around the tensioner pulley. Just place the belt around the motor pulley, and then pull the tensioner pulley toward you and leftward until it clears the belt, then push toward the front of the dryer - and let the tensioner contact the belt on the right side of the tensioner pulley.

And finally, the ribbed side of the belt makes contact with the drum and the motor pulley. The smooth side of the belt is in contact with the tensioner pulley. Good luck, and may the choice words I used during the process be unnecessary for you... for you... for you!

When I went home at Christmas, I saw that my Mom had been using a small bench to keep her dryer door shut. I wrote the make / model of the dryer down and found your website. I ordered the part, and my sister snapped it into place. My mom was so happy to have her dryer door stay shut again!

Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.

Removed 6 screws from the back panel and lifted/pushed the metal back panel up. Removed/sliced out the start switch by hand. Replace the new start switch and tightened all screws. Replaced the new selector Knob and it worked like charm.

I received the replacement part I ordered from PartSelect.com within 3 days of placing the order. I opened the plastic bag it came in. I snapped the part into the holes left vacant by aforementioned abscence of broken part.