YWED5010LW0 Whirlpool Dryer - Instructions

Kit was easy to install and after making sure the drum gaskets were set right the noises ended.

Found a DIY video clip on YouTube...Ordered the parts...I only needed a replacement belt but PartSelect had an upgrade kit that included not only the belt and rear drum support wheels, but also the tensioner arm with a WHEEL instead of just the flat metal belt guide ( which I believe lead to the belt wearing out in the first place) All the parts fit perfectly and now it's better than new.

Had to order idler lever and wheel as the one in the kit would not work. Best to buy part specific for your dryer. Repair was easy, just watch repair video. Sounds like new dryer again

Diagnose the problem. Is it the motor ? Is it the belt ? Order the correct repair kit, use name brand parts to ensure reliability. READ THE SUPPLIED DIRECTIONS. You can use a small wood shim or wedge at the top front corners to open the top . Use a 5/16" socket to remove the 2 screws at the top outside corners. Lift the front panel straight up, supporting the drum as you lift it off. Remove the drum, taking it straight out the front. Install the new drum rollers, install the idler, and then the belt around the drum. Install the drum on the rear rollers, make sure the seal is not folded under. Push the drum back against the seal flange, support the front of the drum with your right (or left ) hand, and sit the front panel on the lower pins, and gently push the front panel to the sidewalls. Feed the belt through the idler and around the motor pulley. This job is easily performed in about 20 minutes. Clean the interior while replacing the belt/idler and drum rollers. With the top lifted, after assembly, test run the dryer to make sure there are no "funny noises" after the repair. Watch especially for the white rub strips on the front edge of the drum. They tend to fold over when attaching the front panel. Job done !

Followed instructions supplied ( very easy)

Took the back off of the dryer and diagnosed the problem. When I saw that the belt was broken I got online and looked for a place to find a replacement. Found Partselect.com and checked out their site and not only did I find the right parts but I also found a video detailing the repair. I purchased a maintenance kit (the belt, the wheels, and the hardware) and the next day my parts arrived and I was able to get the dryer back together in no time at all.

I assumed the drum belt has broken so without looking and tearing into the dryer first. I looked at the model number on parts select and the belt was $43.00. However the maintenance kit wihich included the belt, 2 wheel guides and belt tensioner was only $25.00. go figure. Ordered it and within 3 days it was at my front door. After opening the dryer I noticed the belt was intact. After removing the drum I notice heavy resistance on the motor. Thinking motor bearings were out! The internal motor heaters would drop out and than reset. Opened the fan shroud and found that a sock had fallin into the top lint screen opening and locked up the fan wheel with out the persons knowledge when the screen was than pushed back into place. Alot of work to find out something so simple. hilarious actually. What a relief that it was not the motor and since I had it apart I went ahead and put in the entire maintenance kit anyway. The whole ordeal toless than 1 hr.

I followed the instructions from this website. Repair was simple with the video guide. Repair estimates were for $150 -$200, I spent less than $40 for the belt, new tension idler, and new rollers. It runs like new again. Parts arrived in 2 days! GREAT SERVICE! I'll be back and am telling my friends about your site!

After removing the back & top of the dryer,I determined the noise was coming the idler pulley.I went online w/ model # & found Partselect.com.I ordered the dryer repair kit (at my door in 3 days) which included all the rollers,idler pulley, belt & hardware.It was an easy job to do even tho instructions were for top control panel model (mine is a whirlpool duet- front control) I did try using silicone lubricant on idler pulley, which worked to quiet dryer for a couple days so my wife could use it while I was waing for parts.Two thumbs up to Partselect.com,I will be purchasing all my appliance repair parts from them..I own all whirlpool stainless steel appliances that have been very reliable,but it's nice to know I have Partselect to fix problems as needed.

I watched your video that showed me how to remove the top then the face of the dryer. I then removed the drum and belt,after which I could then remove the support wheels and the belt tension wheel.I replaced the support wheels and tension wheel,the hardest part was removing the little plastic locking keepers that hold the support wheels in place. After that I was able to reinstall the drum with the new belt and reinstall the face and top of the dryer. My 15 year old dryer works great just like new. Thanks

Opened up the dryer and found that the belt broke. Came to this web-sight and was quickly directed to the correct part once viewing the schematics, and then watched the video. The day the parts arrived in the mail, I went to work and managed to get the drying working that night! Thank you for the parts, the video...made it very easy to complete. Sheral

After removing the bottom front panel using a putty knife to pry the upper left and right edges of the panel, I noticed that the long thin drum belt had broken. I went online to PartSelect, and using the Whirlpool model number, found the parts diagrams. Since the dryer is 20 years old, I decided to order the maintenance kit part# PS373087 which includes new idler wheels, retainer clips, and a tension pulley as well as the belt . I found a number of webpages that offer guidance in replacing the belt. Along with the instructions that came with the maintenance kit, I was able to do the repairs and have the dryer up and running in 30 minutes. Remember to remove the door springs before taking off the upper front panel. You only need to loosen the bottom screws on this panel. Leaving them in place helps to align and hold the panel when re-installing it.

After running the unit for a minute or so I removed the back of the dryer. Unable to locate the problem from this vantage point, I then removed the bottom kick plate. Using a small flash light, and turning the drum by hand I discovered that one of the support rollers had burned out the bearings. I went to this web site to see if I could still get parts for the unit. I found not only the part, but a full repair kit. Knowing all the parts would need to be replaced at some point, and that Mom could not afford a new unit I replaced everything. The parts did truly arrive in one day when they arrived I went back to your web site. I had seen instructional videos while looking for the repair parts. After watching the video I removed the dryer drum, removed the parts to be replaced (2 drum support rollers the belt tension roller, and belt) I replaced old with new cleaned entire unit reassembled and it is working like a champ thank you very much for all the parts, and info

Remove the lint filter. Remove top without disturbing control wiring -- turn top on end but make sure it cannot fall. Unhook contacts on door switch. Remove screws hloding front panel and kick plate. Remove door hinge springs. Remove front panel and kick plate.Fish out old broken belt. Remove drum. Vacuum out all the lint. Reposition/replace pulley assembly and wheels. Place new belt around drum. Reinstall drum being careful to properly position the seal at rear. Prop up the drum with a suitable sized article to keep it in position temporarily - or have someone else hold it in position. Thread drive belt through pulley assembly per directions and put over drive hub. Manually turn drum to ensure proper belt and seal positioning. Put front panel back on. Turn drum while inspecting seal -- use putty knife to slip under seal if necessary to ensure its not folded under drum lip. Remove the prop holding up drum. Reinstall door hinges springs.Reinstall kick plate. Reinstall top.

Replaced belt,wheels,idler arm and drive motor.Used video instructions from PartSelect.Instructions are spot on.All replacement parts were correct ans fit like a clove.Orderinig was esaey.Staff was friendly and knowleable.Parts arrived quikly with out using next day service.I will use PartSelect in the future and recomend the company to my coworkers and friens.