NE3313 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daral from Merrimack, NH
- Parts Used:
- WPY54414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Idle pulley frozen
Once I realized the drum was to be removed, the actual repair was not difficult. Because of the location of the pulley, it's best to tilt the dryer. Snap ring pliers are required to remove the retaining ring on pulley. I pulled the damaged pulley from the bearing. A small gear puller was needed to removed the frozen bearing. Lightly oil the new bearing. Installing the drum is a challenge because of the loose belt. I used paint tape to hold the belt on the drum. Download the service manual for good exploded parts views.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tanya from Greenville, NC
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
My dryer belt broke.
I took the dryer apart and used the video on the website that helped a lot on how to install the belt and then we put it back together and dryer works great.
Was this instruction helpful to you?
Thank you for voting!
Blower wheel broken and rubbing on housing.
Removed front of dryer, first the lower then the upper front covers. Removed front drum support, front blower housing cover. Removed belt, and then motor with housing and blower wheel attached. Broke wheel and cover off motor, placed motor in vise to remove threaded nut from motor drive shaft (nut was seized). Reinstalled motor and belt. Installed new housing and blower wheel. Reassembled dryer. Note if old blower wheel had come off repair would have taken half the time and been significantly easier to perform.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brenda from Shelbyville, MI
- Parts Used:
- R9900489
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
The temperature in the dryer always got too hot even on low settings
I was ordering a part for my daughter who needed a high limit switch and a fuse, it occurred to me after reading the troubleshooting helps on PartSelect that this was what I needed to change on my dryer also. With the help of your installation videos my daughter was able to repair her own dryer and save about $150.00 and I too was able to repair my own dryer and now it works great! Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria from Marine City, MI
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer Belt Broke
Watched the video from part select and it was easy. I will always order from part select, I loved the delivery time!! I ordered two belts, one for my dryer and one for my sons. . . My belt arrived the next day and my sons only took two days. . . Now that is service. . Thank you part select
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from saint louis, MO
- Parts Used:
- WPY54414, WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
dryer was loud and making a squeeling noise when on.
for a while the dryer was really loud when on. i took the front cover, and could pin point it to the idler pulley wheel. i would squirt some wd 40 on the wheel just to get by. one day the dryer stopped turning so i thought the belt broke. after following the instructions on this site on now to take off the front panel, and tub holder (the panel that has the lint trap in it, i was able to take out the tub and find that the pulley wheel had broke apart. i ordered the new part and got a new belt at the same time. why not replace while i had it apart. i didnt have snap ring pliers to remove the snap ring so i got 2 small finishing nails that would fit in the holes and was able to pull apart the ring and get it off. i slid on the new wheel, and put the snap ring back on. ii watch the video on how to replace the belt and it was a sinch. the dryer was already apart and to fix it, took about 15 min. for $18 in parts, the dryer has never sounded better.parts select saves me money everytime.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOEL from ALTADENA, CA
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Broken belt
I just followed the intructions from the video on the website. That made the replacement easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlos from Rowlett, TX
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer was shacking really bad
I did it just like the man in the video that was sent via e-mail by ParSelect,.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chris from bakersfield, CA
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
Broken drive belt
I was amazed just how easy it was. It would have been much quicker if I had a nut driver instead of a wrench. The video was great. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerry from New Braunfels, TX
- Parts Used:
- 56000
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Wife let ink pin fall through lint trap and started dryer it broke fan.
Pulled off front of dryer because it made loud noise, lifted clothing drum removed cover for fan and order from model number on fan and replaced. 30 min with help from my son.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Lakewood Village, TX
- Parts Used:
- WPY54414
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broken Idler pulley
removed front, top cabinet, drum, belt and motor. replaced idler pulley on motor. replaced motor, belt, drum and cabinet parts. test ran fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Elk Grove, CA
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dry would not spin fast/ or would scream with heavy load
I took off the front panel removed the drum and took off the belt. I then installed new belt on drum then motor. Then installed the front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from minooka, IL
- Parts Used:
- WPY54414
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dryer was making a real loud grinding noise, like nails on a chalk board.
Really easy popped the lid with a flat head screwdriver, then marked wires for door light and switch, took 2 5/16 bolts to remove front door, then 4 bolts also 5/16 to remove front panel but be care ful and remove drum belt then take panel and drum out. Then took a set of ring pliers to remove wheel slapped new one on.then reverse sreps to assemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Arlington, TX
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door Latch broken
Ordered part ( door latch ) flowed instructions easily fixed same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from phoenix, AZ
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the plastic latch broke
im a car mecanic it was easy
Was this instruction helpful to you?
Thank you for voting!