DBSR453GA1AA Whirlpool Dryer - Instructions

Removed 6 screws from the back panel and lifted/pushed the metal back panel up. Removed/sliced out the start switch by hand. Replace the new start switch and tightened all screws. Replaced the new selector Knob and it worked like charm.

Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.

1st - removed the two screws inside the front door panel. They are somewhat hidden up underneath so you may have to look for them. 2nd - I removed the top of the dryer cabinet by lifting it out of the clips holding it in place. 3rd - removed the two screws (one on each side) in the o=uppper corner of where the side panels connect the front panel. These are about 3/4" phillips head screws. Then the front panel could be moved to one side of the dry. 4th - remove the drum by lifting it up and out the open top area. 5th - add the new belt to the dryer tub (rib side towards the drum) and replace dryer tub to its original position. 6th - reaching in underneath the tub you need to pull the ideler pulley toward the center of the cabinet while laying the belt on the "outer side" of the ideler pulley and at the same time fitting the belt over the small pulley located on the motor. Once that is done, you reassemble in reverse order and should be good to go.

I was cleaning my laundry room when I noticed the gasket needed cleaning. While wiping it off it appeared as though I could remove it and that was my biggest mistake. Once removed it could not be replaced, due to the little parts that held it to the door began tearing off as I tried to put it back on. I ordered a new gasket and had it put on. It did not require any tools, just concentration. I've learned "if it's not broken, don't fix it"! I spoke with several other people and I am the only one who has removed a gasket. Thank you very much PartSelect for your help.

Both parts arrived quickly and were exactly what I ordered. The lint screen replacement part was of higher quality and it works better than the one that came with the dryer. Very satisfied.

Used an allen wrench to remove the heat deflector and used allen wrench to replace it with the new one. HINT!! Do not lean on the inside of the dryer!!!!!!

Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!

Read the other posts - they are very good. On my particular dryer it took two Slide WH and two Slide Dryer Drum Side PS266785.

Most time spent was vaccuming out and removing a softball size ball of lint clogging the dryer - now it will actually dry clothes!

Part select delivery is really fantastic (even though it took me three orders to get it right!).

Took the few screws out replaced the part then put it back together.

I followed the instruction of the first posting for this category and it worked perfectly...thanks for the nice detail...

- Upon receipt from PartSelect, placed new slides in Drum Bearing (this does not come together or as a kit - must order 4 slides AND Bearing separately for this dryer model)
- Loosened Top panel screws (2) from inside door area
- Slid top of dryer off - PAY attention to HOW the top comes out (tabs at the back and slots on the sides) or replacing the top could prove frustrating)
- Loosened Front panel screws (2) and GENTLY leaned the panel forward to access Drum Bearing - no need to REMOVE the front panel but be aware of the switch wires when leaning and the weight of the door if you did not remove that
- Removed old Drum Bearing
- Vacuumend interior of dryer cabinet (especially area leading down to vent)
- Snapped new Drum Bearing into place
- Re-secured Front panel paying attention to drum position to make sure everything still rotated properly and freely
- Reset Top panel - align back tabs first, gently pull forward just a bit until Top slips down over side tabs, then slide back into place and re-secure

Worked like a charm - took about 20 minutes...

took out broken filter and replaced with new lint
filter.

I received the part in record time.(2 days) I had a little trouble getting the case off of the dryer, but the part was real easy to install. I have changed these before with another company and their instructins were not good at all. Your instruction were relly easy to understand, step by step.

Thanks

Pulled off old knob put on new one

I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.

Unplugged dry cord . Removed top and front cover. Removed drum to replace rear Bearing. Reinstalled drum replaced front bearings and sleeve. Reinstalled both covers and plugged in.