CED7011LW1 Whirlpool Dryer - Instructions

I ordered the maintenance kit because it was recomended for my application and the symptoms my dryer was exhibiting. However this kit did not apply to my model. My model contained 4 drum rollers, only 2 came with the kit, and the idler pulley setup was completely different. I should have pulled the dryer apart first to compare pictures to the actual parts. No big deal, prompt refund after a quick phone call to Parts select. I was able to fix my idler pulley with a couple of new nylon washers and a new snap ring to hold it in place. Whirlpool cabrio wed6200sw1.

I purchased the maintenance kit and followed the video on part select.com. Replacing the drum wheels, pully and belt was not difficult. I probably found enough coins in the dryer to pay for the maintenance kit. The only tricky part was getting the cap on the end of the axle. It requires a bit of force applied evenly.

Basically, I just did everything in the Parts Select video - it's what gave me the courage to attempt the repair myself and I am a 61 yr. old woman, who's not in great physical shape! The belt had broken. The two things that gave me the most trouble were disconnecting the tab on the door switch assembly and getting the screws to line up when replacing the front panel - one side lined up fine - the other needed a good push and an "alley-oop" to the side with my hip to fall into place. I did a few things that were not in the video which I think really helped me out. (1) I put an empty quart sized paint can under the dryer drum to hold it up - that really helped - I only had to support it slightly myself when threading the new belt. (2) I put a piece of duct tape across the bottom of the idler pulley to keep that from falling out of the holes when I was threading the new belt - that worked like a charm. Just be sure to remove the piece of duct tape and the paint can before you close up the dryer, if you decide to follow those two tips. (3) I also eventually put something under the front door panel to help raise it up and get it more in line with the two holes that it connects into, which made it easier for me to get it back into place. (4) Have some bandaids on hand - I sliced two fingers on different parts while installing the whole kit. (5) After you are done, either clean out the dryer vent hose or put a new one in - I was surprised by how much lint was clogged up in there. I never repaired any appliance before and if a 61 yr. old weakling like myself can do it, anyone can. Parts Select Rocks - the kit arrived a day and a half after it was shipped out and the video tells you everything you need to know to do this repair yourself and save big money. $49 versus probably $150 for a repairman and $500+ for a new dryer. Dryer is running like new! Would definitely do this again, if this or another dryer broke in the future. Thanks!

After watching your video, and reviewing the directions, I was able to change the rollers, the belt and tension bar with ease. The parts cost me slightly under 50.00 and now the noise is gone and my dryer works great. I am very pleased with PARTSELECT and would use them again. The parts were at my house within three days of placing the order !!!

Found the perfect maintenance kit and helpful repair video on PartSelect.com. Factory replacement parts were delivered quickly along with written installation instructions.Never needed them. Just performed the repair while watching the step by step video. Dryer works great, no noise. A very happy customer.

The videos really make it easy. I put my laptop on the washer next to my dryer and proceeded step by step. I also found the video that mentioned about the screws that may come loose on the baffles. I found several loose screws on the baffles which I tightened and I also found the Drum hole plug loose, so I also tightened the plug. Reassembled the unit and has been working like new since.

My dryer all of a sudden stopped tumbling. When I opened up the machine, it turns out that the drive belt was broken. I simply put in the model number in PartSelect.com and found this kit that came with the belt, and drum rollers. The belt fixed the tumbling issue, and after replacing the rollers, the machine is as quite as a mouse! The instructional video helped show me exactly what to do and expect. This was my first time fixing an appliance, and it only took me 45 minutes!

I had my laptop next to me and paused the tutorial video
as I did each step to chnage the drum rollers, idler pully and belt. Dryer runs great with no more screeching!

Remove the lint filter. Remove top without disturbing control wiring -- turn top on end but make sure it cannot fall. Unhook contacts on door switch. Remove screws hloding front panel and kick plate. Remove door hinge springs. Remove front panel and kick plate.Fish out old broken belt. Remove drum. Vacuum out all the lint. Reposition/replace pulley assembly and wheels. Place new belt around drum. Reinstall drum being careful to properly position the seal at rear. Prop up the drum with a suitable sized article to keep it in position temporarily - or have someone else hold it in position. Thread drive belt through pulley assembly per directions and put over drive hub. Manually turn drum to ensure proper belt and seal positioning. Put front panel back on. Turn drum while inspecting seal -- use putty knife to slip under seal if necessary to ensure its not folded under drum lip. Remove the prop holding up drum. Reinstall door hinges springs.Reinstall kick plate. Reinstall top.

Replaced belt,wheels,idler arm and drive motor.Used video instructions from PartSelect.Instructions are spot on.All replacement parts were correct ans fit like a clove.Orderinig was esaey.Staff was friendly and knowleable.Parts arrived quikly with out using next day service.I will use PartSelect in the future and recomend the company to my coworkers and friens.

I watched the video online in the order section. then just did it after we received the repair kit.

Diagnose the problem. Is it the motor ? Is it the belt ? Order the correct repair kit, use name brand parts to ensure reliability. READ THE SUPPLIED DIRECTIONS. You can use a small wood shim or wedge at the top front corners to open the top . Use a 5/16" socket to remove the 2 screws at the top outside corners. Lift the front panel straight up, supporting the drum as you lift it off. Remove the drum, taking it straight out the front. Install the new drum rollers, install the idler, and then the belt around the drum. Install the drum on the rear rollers, make sure the seal is not folded under. Push the drum back against the seal flange, support the front of the drum with your right (or left ) hand, and sit the front panel on the lower pins, and gently push the front panel to the sidewalls. Feed the belt through the idler and around the motor pulley. This job is easily performed in about 20 minutes. Clean the interior while replacing the belt/idler and drum rollers. With the top lifted, after assembly, test run the dryer to make sure there are no "funny noises" after the repair. Watch especially for the white rub strips on the front edge of the drum. They tend to fold over when attaching the front panel. Job done !

Watching the video from Parts Select for replacing the rollers showed us all we needed to easily replace the wheels as well as the Pulley and belt. It made a gigantic different in the noise and efficiency of the dryer. One of the Wheels was actually 3/4 gone, worn away. Hopefully, this repair will extend the life of an already old dryer. Thanks for the videos that made the repair a 'piece of cake'.

it was easy all the parts were the exact replacement

Found a DIY video clip on YouTube...Ordered the parts...I only needed a replacement belt but PartSelect had an upgrade kit that included not only the belt and rear drum support wheels, but also the tensioner arm with a WHEEL instead of just the flat metal belt guide ( which I believe lead to the belt wearing out in the first place) All the parts fit perfectly and now it's better than new.