NG6339 Whirlpool Dryer - Instructions

My husband pulled drum out of dryer and replaced the idler pulley wheel and decided to replace the belt while he was in there. It's good to have a snap ring tool as it's a pain to replace the snap ring without this tool. Goes alot quicker!

Unplug dryer. Remove lower panel.Remove dryer lent duct. Remove Thermostat fm fan housing. Remove Fan.Remove Fan housing. Remove Motor assy by sliding out, wires lay toward front, allowing room to replace idler pulley and spring. Use lock ring pliers to remove pulley from shaft. Grease pulley/shaft w/high temp grease [I used ultra-hi temp ceramic brake grease-can get in small packets at auto stores].Noise/slippage has all but stopped. Lesson: replace rear rollers and front felt/glides. Belt looseness also caused by worn rear rollers [smaller overall diameter from age]-even though they spin freely

1st replaced limit thermostat because it tested bad; this did not resolve the problem. Initial burn was successful. Heating element would heat but burner would not ignite for subsequent burns unless allowed to cool down for 10 minutes or more. Coils tested at correct values, but a u-tube video said that was not always an indication of a flawless coil set. It was either the coils or the burner itself. Burner would not have been a justifiable expense even though it came with new coil set, so tried the coil set, and it resolved the problem.

I watched a video. The man speaking was Wayne from parts direct. He made the repair go so smoothly. I enjoyed watching him and I hope you include him in more videos. Had dryer apart and back together (after I had to take top back off, to re-attach the door switch, which I forgot. Had a senior moment!!) in 15 min.And working as good as new. Thank you Wayne. Have a nice day. Bryan

DISCONNECT THE POWER. (I got shocked a few times during the diagnoses stage). Remove the lint catcher. Pop the top of the dryer up (there are two plastic tabs along the front of the dryer. Remove the two screws for the lint catcher and open the top of the dryer. Loosen the screws between the side and front panels. Lift up on the front of the dryer to free it from the clips down below. Swing the front panel out of the way to avoid disconnecting the door-open-switch. Undo the two screws holding the bracket onto the gas burner regulator. Replace the coils. Reassemble in the reverse order. It was helpful to open the dryer door to help align the drum and front panels.

went on line to look up the problem troubleshooting a maytag gas dryer. after checking different sites I figured that I needed a coil valve. searched for the part I needed and found the best deal on this site. I ordered the part and and by following the directions. I was able to replace the part on my own.

Installed new coil, helped but have other issues that I'm troubleshooting.

replace two heating coils. Dryer working find.

i removed the door and front panel then removed the two screws holding the coil bracket,disconnected the two wires on coils,set new coils in place and reversed the above process

I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.

I shut off the power supply (pulled plug) . Opened the front access door on bottom of dryer, The two coils sat on top of burner unit, with a plate and 2 Phillip head screws securing them. .I used a small set of pliers to pull the terminals off, then I used a short Phillip head screw driver due to the proximity of the dryer drum close by. The coils slide off, slide the new ones on, re secure the plate with screws, reconnect the terminals, plug in the power cord and away you are for a fraction of the cost.

All the videos said the same thing. If the Igniter works and the gas ignites bit shuts off soon after that, then the coils are bad. I bought the coils and it didn't fix the problem. My bad, I should have put my meter on it to test it before I bought the part and waited a week to get the coils. Now I'm in the process of illuminating the sensors. I will figure it out. Make sure you use the meter. It will save you the headaches.

The round exhaust duct in the back my dryer can be removed simply by pulling straight out. This gives full access to the belt tension wheel. Slip belt off the wheel, remove snap ring with snap ring pliers, remove washer and wheel. Install new wheel, attach belt, and reinstall duct by looking right down the middle to line up properly. Dryer sounds like new again. 10 minute job.

Unscrewed front panel. Pulled off unbroken wire connecter and popped switch and put new one in. Replaced front panel.

Well, this is quite easy really. I found the problem after plucking and chucking a few parts but it was finally the igniter that was the problem. After taking the front section panel off to access the components, take the time to unscrew the igniter and see if it is cracked. That is what happened to my unit. I replaced to the new M series coils as well but the issue was the igniter. Look very carefully for a crack, the one on my unit was very small. You can ohm it out with a meter and if it reads open it is cracked.