Models > DBLR453GT0WW > Instructions

DBLR453GT0WW Whirlpool Dryer - Instructions

Jump to:

All Instructions for the DBLR453GT0WW
121 - 135 of 545
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mark from Teaneck, NJ
Parts Used:
WE18X54
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
My GE Hotpoint dryer would not completely dry clothes due to rusty and clogged flint filter.
I just pulled out the old white frame by hand and replaced it with a new one ordered online. No tools were needed. Simply easily, anyone can do with no required skills.

This saved the appliance from possible damage due to poor ventilation and also save the cost of a handyman to fix the problem.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Walter from Boone, NC
Parts Used:
WH1X2721
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Dryer Start knob was broken
Ordered new knob from you people and simply replaced borken knob.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Maiden, NC
Parts Used:
WE1X1263
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The timer knob
It just slipped on. But, the ease in ordering this part was amazing. I am not mechanically inclined at all. I use repair people for mostly everytning, but, $50 to just look at it was too much!! Then I decided to look online and it was the right choice. I will use and/or suggest PartSelect ;-)
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Augusto from El Cerrito, CA
Parts Used:
WE1X1263
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
timer knob was cracked and did not turn the timer
replaced the old knob. No tools required. Less than 1 second.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Falling Waters, WV
Parts Used:
WE18X54
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Filter metal net for lint has sharp netting
Replacement is easy = Tilt net for lint into opening and set by snapping left side then slide to right to seat into proper seal. Do not force either side when seating.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Rahway, NJ
Parts Used:
WH1X2721
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken Start knob
After finding a matching knob for the broken one on my dryer, I ordered it from this website and within days had my dryer working like new again. Just slipped it on and that was it. No more using pliers to start the dryer. Couldn't have been easier.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Miami, FL
Parts Used:
WH1X2721
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Knob broke
Pulled the old knod off and put the new knob on.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Columbus, OH
Parts Used:
WE18X54
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Old lint filter was broken
Replaced the filter. Was very impressed how quick I received the product, no hassel... Nice...
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Janis from northridge, CA
Parts Used:
WH1X2721
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Knob broke
Easy. Pulled off old one slipped on new one!
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from Santa Ana, CA
Parts Used:
WE04X25996
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
No Heat
Removed gas line. removed control panel, removed top, removed front, removed burner, replaced igniter, put back in. paused and played the video. very easy to do. 42 minutes and I had a few beers.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Rice Lake, WI
Parts Used:
WE4X881
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Broken start swithch from moving dryer
Removed top panel from dryer. Unplugged the 2 wires for swithch, rotated swith, and removed. Reversed the process. Put parts back together.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cheryl from WILDER, KY
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Door handle broke
Called my son-in-law. Easy as pie
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wayne from BAKERSFIELD, CA
Parts Used:
279834
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
Dryer not drying- gas valve coil resistance measured 'Open'.
Unplug dryer first! Remove toe panel with 1/4" nut driver on each lower corner. Gas assembly will be on the right immediately below right of drum. Use a short Phillips screwdriver to break loose two screws retaining hold-down plate on gas valve coils. I used an adjustable wrench to turn the screwdriver on screws which are not easy to apply torque to. Each coil will easily slip off stem. Disconnect catch on plug with very small flat tip screwdriver for each coil, then pull off connector. Ensure the 3-terminal coil goes to the front and the 2-terminal to the rear. Note aligning tips on coils which correspond to holes in hold down plate. Reassemble in reverse order except for toe panel. Plug in dryer and verify gas valve operation and flame presence. Replace toe panel.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Melissa from FOWLER, OH
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Dryer would not heat.
Diagnose that the circuit is functioning up to the igniter. This is done by removing the peep hole cover on the bottom front panel, turn the dryer on and watch for a glowing igniter. My dryer would still ignite the first time because the coils would not show an "open" until they heated up. So if you see the igniter glow it is most likely your coils are bad. Remove two screws from lint trap area on top of dryer. Pry up on top panel at the two clips. Panel is on hinges, so flip it out of the way or just brace it with something enough to keep it off the front panel. Remove the two bolts from inside top corners of the front panel. Use a small punch or screw driver to push in on the tab to release the doors electrical connector. Pull straight up on front panel to remove it from bottom clips. The gas valve is very easy to get to without removing the drum. If needed for inspection or cleaning, just pull back on the belt tensioner to remove the belt from the motor and then pull the drum out. Or just use a stubby phillips screw driver to remove the bracket from the top of the ignition coils. Use a very small flat head screw driver to lift the locking tab on each electrical connector while removing. Remove the coils and place new ones in very same position (note the tab or key way of the coils faces up and are defined in the bracket). Re-assemble all parts making sure connections are tight and drum is correctly mounted. Note: if you remove the drum, return the belt back, in a loop, through the tensioner. This part hurt my head for a moment because I did not pay attention. Also a good idea to vacuum the debris and lint while your in there! As always check to make sure the exhaust pipe is clear. Have fun!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from STOW, OH
Parts Used:
279834
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Dryer would not heat
Followed directions from Youtube video
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DBLR453GT0WW
121 - 135 of 545