DBSR453GB1WW Whirlpool Dryer - Instructions

Just took out of plastic wrapping and put on dryer. No tools needed.

Pulled off old knob and snapped new one into place. Took about 5 seconds. Must be a lame design cause my dryer's less than 2 years old and the knob snapped on the inside and wouldn't turn. Easy to fix though.

Dryer is 3 yeras old. This dryer switch / start knob broke three times. First two GE repair fixed it. Charge was about $75 to $100. Then I found Parts Select, Who what great prices. Switch cost under $10. and took me 10 minutes to install. Dryer works great again. OH, I ordered an extra switch to have on hand.

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

Replaced coils on gas valve.

Watched youtube video to problem shoot. Cause determined to be coils bad. Searched web found Parts Select to be easiest site to deal with and had coils for best price. Followed instructions supplied with parts. Dryer works like new.

I removed the right side panel and top panel from the dryer. I removed the 2 wire and 3 wire connectors from the 2 coils. I removed the bracket holding the 2 coils, replaced the 2 coils, and replaced the bracket. I reconnected the wires to the appropriate coils and replaced the side and tops panels on the dryer. The dryer now lights every time the dryer calls for heat.

My gas dryer would run with heat for 5 minutes in all settings, but kick off and not heat again. Timer would not advance in autodry. Thought it was the cycling thermostat, so replaced that, but did not solve the issue. Ordered the coils, and cleaned out heavily clogged lint from bottom of lint trap, especially right above the fan motor at the bottom of the trap. Received the coils, opened the top and front, took out drum, and replaced the coils. The replacement took less than 2 minutes. Be careful putting the drum back on to make sure the felt is not caught inside the drum. You can give it a spin to make sure. Wear gloves, as I cut myself up pretty good on the edges of the dryer body. The inside of my dryer looks like a crime scene! Anyway, I put it back together, and it runs great. Solved the timer advance issue in autodry, and the heat kicks on and off when it is supposed to. Good luck! Thanks Part Select!

With the help of doityourself guy on the internet

It turns out the back of my dryer timer knob was cracked, so everytime I would turn it it would just slip to any setting/time. This was just the matter of pulling out the knob & pushing in the new one. The other issue I had was my dryer would always run without having to start it. This is because the rotary "start" switch was bad. It just took a philips screwdriver to take the backsplash off the dryer to replace the switch. So easy my wife or kids could've done this!!

Son found out where the bulb was by using YouTube. I googled lamp for model number and your website came up. I ordered the part, it arrived promptly, and my son installed it.

Line up knob. Push on.

stuck it back in the holes just like the original handle. Had to do a little adjustment because I put screwdriver in them too many times to open the door after the original handle feel off, so the fit was loose. Fixed with tape.