3RLGR5437KQ2 Whirlpool Dryer - Instructions

I purchased the dryer repair kit with the drum belt, wheels and idler pulley. I watched the instructional videos online and it seemed fairly straight forward. Breaking down the dryer and replacing the pulleys was easy enough. My problem began when I tried to feed the drum belt around the idler pulley. After finishing the job, the dryer would not turn and the sensor light stayed on. I thought something else was broken with the dryer and spent hours trouble shooting other problems that I was having. Finally I figured out that the drum belt was not installed correctly around the idler pulley. However, I could not get it properly installed from the front of the machine so I tried from the rear still with no avail. I finally had to fish the old belt out of the garbage can that I had thrown away earlier. I lined up the old belt with the new one in the kit and discovered that the new belt was much smaller, so I put the old one back on the drum. Here's the lesson I learned...make sure the belts are the same size before attempting to install. The old idler was responsible for the squeaking and that stopped but I am still using the same old drum belt. Hope it lasts.

Turn off the circuit breaker ( Or remove the Fuse/s )to the dryer,

Removed 2 screws that hold the control cluster to the dryer top. Then I slid the control cluster forward and up to release it from the dryer. then I removed the start button knob to the start switch by pulling on it straight out. Next I removed the six 1/4" hex head screws from back of the removed control cluster. Then using a flat bladed screwdriver I pried up the tab coming off the switch housing. just enought to allow the switch to be turned a quarter of a turn counter clockwise which allows the switch to be removed from the back of the control cluster. Next with a pair of long nose pliers gently pull straight up on the 2 wire terminals attaching wires to the switch. Make a diagram before removing them so that they can be put on the new switch in the same way. Then orient the new switch with its tab located a quarter turn counter clockwise from the hole you pried the old switch tab from. push down on the switch while turning it clockwise 1/4 turn so the tab on the switch drops into it's locking hole. Then using your diagram put the wire terminals back on the switch terminals in the same order and position they came off. Replace the Control panel with the screws you removed. Next position the control panel feet over the holes for them in the top of the dryer and push back a little on the panel to lock it in the correct position. Then take the two longer screws and put one on each side of the panel at the correct angle (not straight up and down) but tilted forward to match the holes and carefully tighten the screws. Next carefully replace the push to start knob on the new switch. Turn the Circuit Breaker (or reinstall the Fuse/s) for the Dryer back on. Then test and make sure that when you select the cycle and the door is closed that pushing the start switch causes the dryer to start. You have done it!

I found that the dryer would not start turning by itself. Could manually help it start and it would run fine. Anyway, after a new set of rollers, belt, etc. found that the motor still would not start by itself. Ordered new motor and it was taken care of. You have to take the back off, remove the belt and remove the tumbler. After that, it is fairly easy. Two screws hold the motor down and then you can take the whole motor assembly out. Be careful removing the fan as it takes a 3/8 socket drive and it is plastic. Two clips hold the motor to the assembly. Needle nose pliers takes care of it. Replace and all should be good.

actually i found your site before i even looked at the dryer,thats how i knew to check for the thermal fuse.
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)

After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.

My 14 year old son did it as I supervised! Pulled the dryer out on a dolly, unpluged the dyer, removed 9 hex head screws to remove the back cover, removed and replaced the thermal fuse, located next to the exhust outlet, set the cover back on, moved the dryer back in with the dolly. I had the thermal fuse over nighted to me for a total price of $35, figured I saved at least $150 on a service call by Whirpool.

First it was a process of alimination to find out why it was dropping out. After the problem was found it was just a matter of replacing the holding coil on the gas valve. Thank you fred kenney sr

1. Disconnect dryer from electrical outlet. 2. Pull dryer out and disconnect the exhaust tube from the back. 3. Remove the screws at the top of the dryer back ( 3 ) and remove the top of the dryer. 4. The service instructions will be in a bracket on the top right. I didn't use them because I have done this job before. 5. Continue to remove the screws holding the back to the sides. There will be a lint collector attached to the back panel by three screws. This must be removed first, then the screws along the edge of the back panel. 6. Pull the back panel up and away from the sides and set aside. You will see two lower rollers attached to this panel. 7. Look under the drum and you will see a idler arm and roller in front of the electric motor and a little to the left. Notice that the drive belt is looped around the roller. Unloop the drive belt from idler and roller. 8. Lift the drum of the dryer up and out of the dryer. 9. Replace all the rollers (4) by removing the plastic "star" on the roller shaft. This can be done using a small screw driver. 10. Once the rollers are replaced, place the new drive belt, ribbed side facing the drum around the drum. Lift the drum up and into the dryer enclosure, making sure the rollers in the front of the drum are in the ridge groove. 11. Lift the back of the dryer in to the dryer enclosure, again making sure the rollers are in the rear groove. Turn the drum by hand to make sure the front seal is flush to the front of the dryer and that the front rollers are in the front groove. I2. Install drive belt around electric motor shaft ( ribbed side facing the shaft), lift idler arm up while running the non-ribbed side of the belt around the roller on the idler arm. 13. Install the back panel using the remaining screws. 14. Install the top of dryer by sliding it into the front panel and securing with the last three remaining screws, these 3 screws go on the top of the back panel. 15. Replace exhaust hose and replace dryer into space it formally occupied.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair.

The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.

I recommend you order the idler pulley as soon as you start to hear the unusual noise indicating metal against metal. Replace the idler pulley before it fails and possibly causes more damage to the drive system. Simply removed the power cord at the back of the dryer and then the multiple screws holding the back panel in place as well as the clip holding the exhaust vent in place. You may need to remove the top panel to access a few of these screws. A diagram of the belt routing is in the paperwork I found behind the front lower panel of the dryer. This too is easily removed with just a few screws.

I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)

I unplugged the dryer,removed the two small screws on the front of the dryer and pulled the bottom forward. The two wires connected to the door do not have to be removed. With an electrical tester using the Ohm setting I tested the Radiant sensor and the Gas Valve coils. The two terminal coil was DOA. The dryer can be operated with the front open as long as the door wires are connected. Symptons: The igniter would heat up and not release gas. My repair was successfull due to this awesome website and the super fast shipping service. AAAA++++

the ignitor did not glow red checked thermal fuse by exhaust duct. fuse open replaced thermal fuse