MED7230HC2 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carl from MARION, KY
- Parts Used:
- WPW10359272
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from WOODBURY, MN
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lint screen was not catching lint and sending out the dryer vent
replaced dryer lint screen with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from CAMARILLO, CA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer was making noise - thought it was the belt, turned out to be the tensioner.
I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from DINUBA, CA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Repair video made it easy
Just follow the repair video, it was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rory from LEESBURG, VA
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dryer kept throwing the E1 error indicating the thermistor needed replacement
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from CARY, NC
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- braulio from FORT WAYNE, IN
- Parts Used:
- WP3387747
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Not heating up
I just took the old element replaced with the new one i order from this site, I save some money was really easy so proud of my self...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from BENZONIA, MI
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screen ripped
Dropped new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from MUNCIE, IN
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
dryer was making a grinding noise
I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from ONEONTA, NY
- Parts Used:
- WP8577274
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
The dryer would shut off mid-cycle.
I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from St. Louis, MO
- Parts Used:
- WPW10512946
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dean from MAGNETIC SPGS, OH
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
pulley bad
pull the back off and replace the pulley.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from ALBANY, OR
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lint screen tore and had a side that was loose so it didn't catch all the lint and cut your fingers
Removed the old screen and simply put in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from PASADENA, TX
- Parts Used:
- 279640
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Idler pulley broke off.
Took back panel off, and it was really easy putting the new idler pulley in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Linthicum Heights, MD
- Parts Used:
- W10837240
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Loud scratching noise, very loud
Lubricated pulley wheel which temporary reduced noise. This verified what was making noise. Looked up the part on partselect.com and ordered it. Recieved idler pulley with bracket in just a few days.
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and removed old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and removed old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done
Was this instruction helpful to you?
Thank you for voting!