WGD7120HW1 Whirlpool Dryer - Instructions

I replaced the thermos fuse, thermostat, igniter kit, and the M series
new style coil kit. The problem was the M series coil kit. I replaced
the other parts because this dryer is over 10 years old. I also brought
the radiant flame sensor. I spent $126.19 in parts plus shipping. If I just
just replaced the coil kit it would have 18.61 plus shipping. A new gas dryer like I have would cost about $459.00. I hope to get many more years out of this dryer. The hardest part of this repair for me was getting the front panel back on. I saved the parts that were good for futher repairs. I replaced the drum belt several years ago, still looks in good shape. I think this is a great DIY site. Just follow their instrutions. Somtimes I'll take a picture of the part before I remove it, just to be sure I replace it right.

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

Replaced coils on gas valve.

After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.

The design of the dryer did not make the conversion easy, I had to disassemble the entire front end, top and remove the drum. The kit included a new spud that's it (22.00?). Anyway the gas valve is convertible from NAT to LP only requires turning a portion of the valve about 25 degrees. I managed with a screwdriver as I could not locate my snap ring pliers(just moved). The directions were spot on, read them through once before you start.

sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.

Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)

Replaced 4 wheels and new belt

Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pulley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.

remove 3 screws vent comes out put new part in works grate just like new a gain

I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.

Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.

Removed the dryer door, unscrewed lint vent.