WGD4985EW1 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- john from OLYMPIA, WA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Noisy sound from dryer
Just like video except there were two screws in back to take control head off. Be prepared to have shop vacation ready. Clean dryer duct too. Have bandaids ready. Plastic triangles are not easy to take off, video makes it look easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Laguna Niguel, CA
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would not heat sometimes
Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open). Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Santa Maria, CA
- Parts Used:
- 279311
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
No Heat, no ignition in burner
Our dryer would not heat and it seemed that no gas was coming from the regulator. The igniter was working fine but the burner never turned on. To check the problem, i followed the instructions to remove all body panels until I had access to the burner assembly. I dismantled both gas valve coils and tested each one for open or closed circuit using my multi-tester. I found that the three terminal gas valve coil was an open circuit and was not functioning so I ordered a new one from PartSelect and within just a couple days, had the drier back up and functioning. I also replaced the igniter due to a malfunctioning igniter that has been changed by the manufacture. I must say that PartSelect has the fastest shipping I have ever seen. One part I ordered was at my door in less than 24 hours and I only paid standard shipping...un real! OUTSTANDING....5 STAR SERVICE
Was this instruction helpful to you?
Thank you for voting!
dryer would not turn on
checked to see what the problem might be according to your website, ordered the recommended parts, received parts within 3 business days, watched video on website with instructions, replaced parts and surprise, dryer works as if nothing ever happened. thank you for the straightforward, no nonsense information and video provided in your website and the promt efficient service
Was this instruction helpful to you?
Thank you for voting!
Got heat only on start of cycle and no repeat of flame. Suspected coils on gas valve.
I used a multi meter to find coils failed in warmed temperature condition.
I tested main switch for different cycle operation. Main switch was worn out inside and not making good contact for soft cycles.
This dryer is 25 years old. I chose to replace all the sensors, fuses, ignitor, gas valve coils, cycle switch and thermostat.
This was cost effective for me, because now, I actually have a good dryer that might just last another 25 years. I might replace the drive belt soon. I'll order from Parts Select. This was easy and fun. Thanks!
I tested main switch for different cycle operation. Main switch was worn out inside and not making good contact for soft cycles.
This dryer is 25 years old. I chose to replace all the sensors, fuses, ignitor, gas valve coils, cycle switch and thermostat.
This was cost effective for me, because now, I actually have a good dryer that might just last another 25 years. I might replace the drive belt soon. I'll order from Parts Select. This was easy and fun. Thanks!
Was this instruction helpful to you?
Thank you for voting!
Replaced two parts in the gas heater assembly
I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with the new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Novi, MI
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Heat Would Not Come On
After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.
After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lot of time and money if I had read that earlier.
After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lot of time and money if I had read that earlier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracie from Culver City, CA
- Parts Used:
- 279311
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
dryer worked but no heat
Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- 72017
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manolak from MURFREESBORO, TN
- Parts Used:
- W10861521
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Door Gasket tore out
Put high temperature glue on first, then put door gasket over the high temperature glue and then let it set for 24 hours. It worked fine....
Was this instruction helpful to you?
Thank you for voting!
dryer had no heat, all other functions worked
After replacing the heat element as a guess, (which did not fix it), I measured voltage with a DVOM, found lower cut off switch in op, And thanx to some tips on parts select I ordered the the Thermal cut off kit, fast shipping, installed very easily and all is working properly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Colleen from CAPE CORAL, FL
- Parts Used:
- WP3406107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer continued to run with door open
The video provided by this site on YouTube on this topic was perfect. Saved us a couple of hundred dollars DIY rather than repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Glenside, PA
- Parts Used:
- W10874409
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint screen torn
Lint screen on my 30-year dryer was torn. Ordered the new screen here with just the part number, fits well. Very helpful website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from LONG ISLAND CITY, NY
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Time clock not moving .Not enough heat
Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from BIRCH RUN, MI
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
the dryer was making squealing noises when it first started.
We watched the video at whirlpool.com! Made it so simple anyone could have done it!
Was this instruction helpful to you?
Thank you for voting!