CSP2940HQ0 Whirlpool Dryer - Instructions

I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.

this was a super easy job! i unplugged the dryer, removed the back panel, located the fuse on the bottom left side, replaced it, put the panel back on, plugged it back in and IT WORKED! this was the first appliance repair job for me and i am so glad i found this site. it probably saved me $100.00 or so doing it myself. thank you!!!

I watched the video several times before beginning, which was very helpful. As I didn't have the tool that was recommended in the video, I used pliers, which although took longer, worked out fine. I also used pliers to pull the wires off of the old thermal fuse. My dryer had been not working for 2 months, so I was very pleased that I was able to watch a very detailed video, order the parts on the same website, and receive them very quickly (within couple of days.) My daughter who lives in another state googled my dryer model number with a description of the problem and found your website. She sent me the link of the video to watch as it appeared very easy to understand. She and I both were very impressed by the step-by-step instructions on the video, including a list of all the tools required. I am an 81 year old woman and had no problems fixing this by myself with the assistance of your website. I have recommended this site to several of many friends and family members. Thank you!

Dryer works - thanks to a new fuse. Glad I tried this before just buying a new one. Video for my model indicated the fuse was located in the back and actually it was difficult to get to in the front. So extra time was wasted trying to get to fuse in the back. Thank you for the part!

There was no heat but the dryer would operate properly in all other functions. I checked the ignitor (gas dryer) with a meter and it was okay. I traced the circut back and ended up at the thermal fuse and it was "open" I jumped it out and the dryer started to work. I knew the problem was the thermal fuse but more importantly why did it blow. Further investigation showed excessive lint in the duct. Needed to take the exhaust system apart and clean out the lint. also replaced the flexible dryer (too difficult to clean) and to make sure that I didn't over work the high/low thermostat and would be doing this repair again in the near future I replaced that also. Be careful and do not jump out the fuse and use the dryer as this will cause a fire. I did it to prove the problem only... Dryer works well again and we will probably get another 5 years out of it!

Al
hrguy@comcast.net

It took me 5 minutes to find PartSelect's site, read the comments about the most common problems and identify the solution. The exploded views were a great assist, as it wasn't obvious where the thermal fuse is located or which access panel to remove.

It took less than 5 minutes to remove the rear panel and install a temporary jumper to verify the blown fuse was the only issue. With the new fuse in hand, replair took another 5 minutes.

A word of caution to anyone replacing is fuse - I found that the exhaust vent pipe to the wall was full of lint and nearly blocked. This is a potential fire hazard. While enough air was passing through the flapper vent to make it look like it was OK, the exhaust resistance is what caused the overheating and made the fuse blow.

I spent more time cleaning out the vent pipe than replacing the fuse, for a total of 25 minutes. I strongly urge all dryer owners to physically inspect the exhaust duct annually.

PS Drying time has decreased by 30-40% since the repair.

I studied the wiring diagram on the back of the dryer. I diagnosed a bad thermal fuse (no continuity). Found the part online at Part Select. The part came a few days later and I was back in business. Great Service.

There were two tricky parts - one, was locating the part to repair on the dryer. One set of instructions said it was on the back of the dryer behind the panel. Once I removed that panel I realized that the thermal fuse was on the front. After I identified where the part was (bottom front), the second tricky part was getting to the screw. You just need a mini-socket set and relatively small hands. A magnetic light that can attach to the dryer while you are working is also useful. This would have been a 30-45 minute job had I known precisely where the part was that needed replacing. Otherwise, this was relatively easy.

NOTE: Please make sure the dryer is un-plugged any time you are reaching into the access panel with your hands or a tool. There are exposed connections everywhere. After using the diagnostic testing instructions (usually attached to the inside of the front panel) I determined it was a faulty Thermal Fuse. The PartSelect video instructs you to take half the dryer apart to access the Thermal Fuse, but I found it easy enough to just access it with the front panel removed. I used a small 1/4" drive socket to remove the single hex head sheet metal screw holding the Thermal Fuse in place. I then slid the 2 wires off, noting which went to which lug. Installed the new thermal fuse and after starting the screw by hand, tightening with the small socket wrench. It is a bit tricky to reconnect the wires as you are doing it all by feel, but it's a lot easier than taking half the dryer apart. Also, make sure you check the exhaust path for obstructions, that might be why the ThermalFuse blew in the first place.

Longest time needed was to determine what cause was. After that ordering part from PartSelect was very easy and saved me money. Part arrived before time given, part was correct and installed without problems.

Attempt to start dryer normally. Turn timer dial to high heat setting. Press the Push To Start button. Verify plug is secure in wall outlet. Got to breaker panel to verify breaker is not tripped. (Sometimes breaker may trip but visually appear no to be tripped). Reset breaker to maker sure breaker is in the on position. Attempt to start dryer normally. If dryer did not start proceed. Get a multimeter. Remove plug from wall outlet. Slide dryer from wall. Remove exhaust duct from bottom of dyer. Use multimeter to check voltage at wall outlet. Verify 120 to ground and 208 between hot legs. Remove rear cover if main dryer unit and rear of control unit. Connect the multimeter to rear of control panel rear of push button. Turn meter to ohm setting. Push the start button to see if there is continuity. Release the button to verify no continuity. Next major part of curcuit is the thermal fuse. Look on lower left area of dryer. With multimeter in Ohm mode place the leads on the light blue wires. If no continuity replace thermal fuse

Replaced Thermal fuse, hardest part was getting behind the drier to disconnect the gas & vent line.

I remove the back panel then look for thermal fuse.. so easy to replace.. thank you so much ..

Removed the old screen and simply put in the new one

I made sure air vent was clear and clean. I removed front panel of dryer unit, located fuse, removed wires, tested fuse with ohm meter, which was defective. Tested new fuse placed back in dryer reattached wires. Cleaned out inside of dryer, replaced front panel. Now works like new.