Models > YWED7120HC0 > Instructions

YWED7120HC0 Whirlpool Dryer - Instructions

Jump to:

All Instructions for the YWED7120HC0
121 - 135 of 376
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Allen from KENNETT, MO
Parts Used:
WP8577274
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Shutting off and had to wait before could turn back on
Followed online video very easy and dryer works like new one....
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gerald from Yucaipa, CA
Parts Used:
W10837240, 661570
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
The bearing on the idler pulley went bad, squealing
Took the dryer apart and replaced the idler pulley with bracket and the drive belt
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gus from RIVERSIDE, CA
Parts Used:
661570
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Belt Broken
Watched video & took my time. It went easy
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sean from ROCK HILL, SC
Parts Used:
W11086603, WP3387230
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Part broken in half
Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Travis from GARRETT, IN
Parts Used:
W10837240
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Very loud squeaking!
Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from WOODBURY, MN
Parts Used:
W10120998
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
lint screen was not catching lint and sending out the dryer vent
replaced dryer lint screen with new.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from CALIFORNIA, MO
Parts Used:
661570
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Broken belt
Disconnect gas line and vent hose,removed top and back covers to install belt.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cindy from BENZONIA, MI
Parts Used:
W10120998
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Screen ripped
Dropped new filter in.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donna from CARY, NC
Parts Used:
W10120998
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rory from LEESBURG, VA
Parts Used:
WP8577274
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Dryer kept throwing the E1 error indicating the thermistor needed replacement
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rod from YORBA LINDA, CA
Parts Used:
WPW10446781, W10837240, 661570
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
Loud Dryer
Please do not buy parts from Parts Select. My order was not shipped the next day (as advertised on the web site), but instead 3 days later. I paid an extra couple of dollars for expedited shipping, which did made no difference (except for a couple of extra dollars for Parts Select to pocket).

When I emailed customer service to complain, I never received any response. I can't believe that customer service can be so unimportant in such a competitive marketplace. And with the power of social media, you would think customer service would be a big differentiator.

I ended having to buy another part (the igniter). I found a different vendor with better prices and a commitment to satisfying customers. I got my part in 3 days for cheaper shipping than the starting point of Parts Select shipping. So I guess I should thank Parts Select for forcing me to look elsewhere because I found a better place with better prices and better shipping and better customer service!
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
braulio from FORT WAYNE, IN
Parts Used:
WP3387747
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Not heating up
I just took the old element replaced with the new one i order from this site, I save some money was really easy so proud of my self...
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from MUNCIE, IN
Parts Used:
279640
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
dryer was making a grinding noise
I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from ONEONTA, NY
Parts Used:
WP8577274
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set
The dryer would shut off mid-cycle.
I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Trevor from Puyallup, WA
Parts Used:
279640
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Squeaky tension pulley
Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the YWED7120HC0
121 - 135 of 376