WED7120HC1 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Candido from GREENVILLE, TX
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dryer won't start.Only make a click noise.
Remove top,front and panels.change thermal fuse and outlet thermistor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyle from HANOVER, IL
- Parts Used:
- WP8577274, WP22002263
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
Dryer won’t start
Drum belt broke. Found drive shaft belt guide broke. Replaced pulley wheel since I had it apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from WICHITA, KS
- Parts Used:
- WPW10314173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Loud squeaking noise
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from CUMMING, GA
- Parts Used:
- WP3387747
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Heating element went out
A) Watched video of repair on site.B) Looked around for competitive prices and decided on PartSelect because of original parts, price, and 1 year guarantee.C) Proceeded to take dryer apart like video showed. Error was my dryer front panel has two screws covering the heater box and that was all I needed to remove and replace heater instead of dismantling the back. Good news though was, I removed all the lint build up in the machine so not a waste of time. Be sure not to touch the new heater wire coils as oil from your hands will destroy the heater prematurely. Heater was original Whirlpool ! I'm a happy camper.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Maple Valley, WA
- Parts Used:
- 279787
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dryer motor bearings failed. Motor wouldn't start.
Disassembled dryer. That was the hard part. Figuring out how to get the top off the dryer so I could get the drum out took the most time. The end caps on the control panel had to be removed by forcing them outward to release the plastic catches. Then the bottom corner screws were removed to allow the panel to swing up out of the way. The top panel could now be removed. To gain access to the belt and tensioner the blower and ducting off the front of the motor had to be removed to remove the belt. Now the drum was able to be lifted out. The motor swap was a cinch with no wiring modifications required. Reassembly was the reverse, with the most difficult thing being tightening up the blower fan. This required putting a wrench on the belt end of motor shaft and holding it while reaching thru a narrow gap on top of the fan ducting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from GARRETT, IN
- Parts Used:
- W10837240
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Very loud squeaking!
Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from MARION, KY
- Parts Used:
- WPW10359272
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gus from RIVERSIDE, CA
- Parts Used:
- 661570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Belt Broken
Watched video & took my time. It went easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SALLISAW, OK
- Parts Used:
- WP3387747
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Heating element went out.
Followed the instructions all went good except for the sliding the shield back in it didn't want to go back in but it does fit. Dryer works like new again.
Was this instruction helpful to you?
Thank you for voting!
Part broken in half
Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from KENNETT, MO
- Parts Used:
- WP8577274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Shutting off and had to wait before could turn back on
Followed online video very easy and dryer works like new one....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from WOODBURY, MN
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lint screen was not catching lint and sending out the dryer vent
replaced dryer lint screen with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CALIFORNIA, MO
- Parts Used:
- 661570
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken belt
Disconnect gas line and vent hose,removed top and back covers to install belt.
Was this instruction helpful to you?
Thank you for voting!
The bearing on the idler pulley went bad, squealing
Took the dryer apart and replaced the idler pulley with bracket and the drive belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CREST HILL, IL
- Parts Used:
- W10837240
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Idler pulley seized
The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and remove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.
Was this instruction helpful to you?
Thank you for voting!