Models > WED92HEFC2 > Instructions

WED92HEFC2 Whirlpool Dryer - Instructions

Jump to:

All Instructions for the WED92HEFC2
121 - 135 of 411
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Charles from SALLISAW, OK
Parts Used:
WP3387747
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Heating element went out.
Followed the instructions all went good except for the sliding the shield back in it didn't want to go back in but it does fit. Dryer works like new again.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carl from MARION, KY
Parts Used:
WPW10359272
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Socket set
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rory from LEESBURG, VA
Parts Used:
WP8577274
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Dryer kept throwing the E1 error indicating the thermistor needed replacement
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
braulio from FORT WAYNE, IN
Parts Used:
WP3387747
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Not heating up
I just took the old element replaced with the new one i order from this site, I save some money was really easy so proud of my self...
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOHN from PUNTA GORDA, FL
Parts Used:
4392065
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Will Not Tumber
I use the manentance kit that was not the problem. I end buying the drive motor and that was it. I was happy with the service I got from part select, overnight mail what more could I ask for? I am also glad I replace everthing with mainentance kit. Thank you for your help john degnan
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rod from YORBA LINDA, CA
Parts Used:
WPW10446781, W10837240, 661570
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
Loud Dryer
Please do not buy parts from Parts Select. My order was not shipped the next day (as advertised on the web site), but instead 3 days later. I paid an extra couple of dollars for expedited shipping, which did made no difference (except for a couple of extra dollars for Parts Select to pocket).

When I emailed customer service to complain, I never received any response. I can't believe that customer service can be so unimportant in such a competitive marketplace. And with the power of social media, you would think customer service would be a big differentiator.

I ended having to buy another part (the igniter). I found a different vendor with better prices and a commitment to satisfying customers. I got my part in 3 days for cheaper shipping than the starting point of Parts Select shipping. So I guess I should thank Parts Select for forcing me to look elsewhere because I found a better place with better prices and better shipping and better customer service!
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Scott from MUNCIE, IN
Parts Used:
279640
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
dryer was making a grinding noise
I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JENNIE from NORTH ROYALTON, OH
Parts Used:
4392065
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Drum quit turning due to broken belt
Followed the included instructions in the Maintenance kit. Very easy to understand & follow. Only advice is to have an extra set of hands to assist in re-installing drum w/ the new belt. Entire disassembly & reassembly could be done w/ basic hand tools but went alot quicker using a cordless drill w/ a set of nut/screw driver bits.
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from SCHENECTADY, NY
Parts Used:
4392065
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Broken dryer belt
Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and old belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
HARRY from OZONE PARK, NY
Parts Used:
WPW10208415
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Broken hinge on door
Took door off with a Phillips screwdriver went to hardware store with door so he could match up the 6pt screwdrivers that were needed.
No more then 1 hour to do.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Henry from CHEYENNE, WY
Parts Used:
4392065
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Noisy, screeching, sounded like roller bearings were shot
Watched the video, followed the printed instructions for reminder when necessary. Needed a second person briefly to hold the dryer tub when installing the new belt, and also when removing/replacing the front panel. Beyond that, it was straight forward and relataively easy to do. Solved the noise problems and it dries more evenly now as well. The one thing the instructions don't say is to check the rear canvas seal when the tub is re-inserted into place to assure it doesn't fold back on itself.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
curtis from STOCKBRIDGE, GA
Parts Used:
279640
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
replace idler pully
first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Allan from JOHNSTON, RI
Parts Used:
4392065
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
belt worn
replaced rollers, belt and pulley. Video was very helpful
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Margo from FOX ISLAND, WA
Parts Used:
4392065
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Dryer was making bad noises like a bearing was going out, then it got worse and sounded really loud, so I couldn't even run it.
Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joe from St. Louis, MO
Parts Used:
WPW10512946
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WED92HEFC2
121 - 135 of 411