7MWED6613HW0 Whirlpool Dryer - Instructions

unplugged from elect power.took off front lower panel.removed heater heat shield w/1/4 in nut driver,could see heat element. it looks like at thin metal twisted phone cord. i used a continuity tester to establish if there was a break in it. there was. i removed 2 1/4in screws on the right side of the element,marked wire placement slid out old element & slid in new one put screws back in connected wires,put heat shield back on . tested dryer ,ok good to go put on front cover.!!!!! PS sears parts wanted 15$ more

Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done

Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.

Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.

So simple.... I have no idea how to fix anything but I took a crack it. Looked inside and pulled out the resistor. I noticed the coil was broken so I replaced it with a newn part and reinstalled it. Worked like a charm. Saved myself alot of money!!!!

The dryer stopped heating. Took the front lower panel off of the dryer and obtained the troubleshooting instructions stored there. Used an ohmmeter (most volt meters also have an ohmmeter) and tested all the electrical components one by one (thermostat, thermal fuse, heater coil - following the troubleshooting instructions provided with the dryer) and found that I didn't have any resistance across my heater element. Removed it and sure enough there was a break in the heater coil. Ordered a new heater element from PartSelect for less than $50 and replaced it myself. Saved myself a good bit of money repairing my dryer myself. It was very straight forward and easy. If you can follow easy to read instructions you can do it.

I followed directions found on several similar YouTube videos since the instructions included in the Whirlpool parts kit were not for my model dryer. I found that the original idler pulley was not rotating and the belt had worn a groove through it. I replaced all 4 roller wheels, idler pulley and the belt. Problem solved.

this was very was very easy. But I deviated from the You Tube instructions. One to release the motor pulley. I needed to use 2 adjustable wrenches for a longer lever. I needed to use a hammer to help release pulley. Second to remove the dryer cable I needed to use a small screw driver to aid in the release. ---- the part from the company was a perfect fit.

Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

Removed top and back covers. Placed new pulley and retaining clip in place. I had to remove a couple of drum supports to put belt on. Probably didn't have to remove top.

I disassembled the dryer, replaced the pulley (which was noisy), and the belt.reassembled, only to find out that the drum would not turn freely. checked all my procedures and kept having the same problem. Finally after 3 frustrating hours, I took the back off and noticed that idler arm was tight against the motor shaft, because the too short belt didn't allow for the clearance needed. Had too take everything apart ,another hour, went and found one at our local repair shop, reinstalled everything , after another two hours runs fine. would appreciate a refund. And please check your part numbers in the future. Would hate to have someone else go through what i experienced.

Replaced high limit thermostat and thermal cutoff. Dryer works like a champ. Reviewed couple of YouTube videos that showed clearly how to
get to the effected parts, test them and replace them. I had an old front loading dryer once before that I repaired a couple of times but these parts were accessible by removing a panel on the rear of the unit. The procedure was more involved with this unit. After studying the videos and getting a feel for what was involved, the process, while involved, was fairly simple and putting the unit back together was also fairly easy. Replacement parts did the trick. Very happy.

I simply followed the video and apart from a couple of areas that were not relevant to my model, everything went exactly as illustrated. The video is excellent and made the repair so easy.

The only issue I experienced was being short two rollers, as the parts diagram did not clearly show that there were two rollers in the back and two in the front.

A kit, with its own part number should be prepared that would show 4 rollers and belt as the recommended required parts.

It was an easy fix, I just did half the install a second time.

Disconnect power supply, remove power cord from dryer, remove dryer vent tube from dryer, remove 2 Philips screws from power connection on dryer, remove nuts from back of dryer, remove back of dryer. Locate idler pulley at bottom of unit at the rear of the motor, pull pulley back to loosen belt and remove from pulley, remove pulley retainer clip, remove pulley and rear washer from shaft and inspect shaft for wear or rust. replace washer and pulley (no specific direction to replace them, washer first then pulley). Reverse above procedure to reassemble. This is for a front load dryer, a top load dryer is different.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.