7MWGT4027HW0 Whirlpool Dryer - Instructions

I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the glow plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.

My 80 series Kenmore dryer wouldn't start so I looked online for a solution to the problem. One of the sites I found stated that the problem could be as simple as a thermal fuse if other potential issues could be ruled out. I ordered the part on a Monday from PartSelect with standard FedEx ground shipping - stated it could be 3-5 business days. To my amazement, the part arrived the next day! Awesome!!! I watched the video on the PartSelect site to make sure I knew how to fix it, then followed the easy instructions. All I needed to do was use the nutdriver to remove the back cover from the dryer, unplug the two wires going into the thermal fuse, remove the old fuse, and pop the new one in. Then I just plugged the wires into the new fuse, replaced the cover and voila, the dryer worked like a champ! Thank you PartSelect for saving me a needlessly high repair bill!!

Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.

Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website

I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!

Went on this website and found a story that was similar. I ordered the parts which arrived quickly and I replaced the Thermal Fuse and heating element and it was fixed! The whole repair cost me $24.88! Way cheaper than calling a repair man.
Heater thing was part # 3387134
and the fuse was 3392519

I unplugged the appliance and turned off the gas supply. I removed the exhaust hose by loosening the clamp with a nutdriver. I removed the back panel screws with a nutdriver and removed the panel. I pulled the wire connectors off of the thermostat and thermal fuse. I removed both parts using a screwdriver. The thermostat terminals were slightly different, but the new style terminal ends came with the thermostat. I cut the old style terminal ends off of the old wiring with wire cutters. I stripped the wires and crimped new ends on the wires. I replaced the parts and wiring in the reverse order of removal. I replaced the back panel and exhaust hose. I turned on the gas supply and plugged in the dryer. I turned the dryer on to test it. It worked well. No problem!

Followed simple instructions to replace two pulleys and belt. The Virtual Repairman helped me identify the cause in minutes. Took another 5 minutes to place the order and the part arrived two days later. Saved $125 at least. Thank you!

john

Tipped washer on its back & tookold Washer pulley assembly off & put new one on.

I watched the PartsSelect video. I was hoping for the tub with the slots in the tub mounts, but mine didn't have them, so I had to lay it down on its back. The only thing I did that was not in the video was I placed a 2" thick closed cell foam knee pad I had on hand between the tub and the back of the housing. When I laid it down, the tub was elevated by 2". This made reaching the two rear rods a little easy. It seems that there would be a more robust way to achieve the dampening affect, but I guess this is cost effective.

It's strange that I searched for my issue several times and only saw recommendations to level the washer. It was level. Then one day I ran across the suspension rod resolution. It didn't do it on every load, but after a year of my wife nagging me and threatening to get a new washer, I finally fixed it. The biggest issue is just logistics in a condo hallway and a little leaking water. I also replaced my hoses. Should be in good shape until the next thing.....

Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent

Thermal fuse was blown so I replaced it. Still no heat. Hi-Limit thermostat and Cycling Thermo. had continuity as did flame sensor. Igniter tested 66ohms. I placed a wire jumper across the Hi-Limit and the igniter glowed, solenoids opened and gas came on. I orderd the Hi-Limit and since both "overheating" limiters were defective I decided to order the cycling thermo just in case. The Hi-Limit was received in 2 days but the Cycling Thermo was backordered. In the meantime my wife got antsy so I went ahead and installed the Hi-Limit and put her back in service... ...for one load. I wasn't certain if I had fried the "limiters" again but since they had continuity and I could measure continuity all the way to the Igniter I decided that it HAD to be the cause. I ignored the flame sensor since it never came into play without the igniter glowing... The igniter arrived and measured 56ohms. Hmmm... After installing the problem was solved. Word of advice: If the thermal fuse is blown and even if all else in the circuit SEEMS ok, go ahead and order the Fuse, Hi-Limit and Cycling Thermos, and the Igniter. It will take you about 30 minutes to install and you'll reduce your out-of-service time! Good luck!

Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!

For the Ignitor - As involved as taking the dryer completely apart sounded, it was super easy. 1-take out the lint trap and remove the two screws there. 2-Pop open the top with a screw driver and swing the top completely over/back. 3- remove the two screws holding in the front panel and remove the panel. 4- loosen the belt by pushing on the tension roller under the drum on the right and remove the drum (its super light) use the belt as a handle. 5- remove the screw holding in the ignitor and replace it with the new one. Be careful to not touch the new ignitor. Then go backwards putting it back together.

Following what the video shows how that they send with your part email, confirmation or receipt!! Easy Peasy!!