LRE7800W1 Whirlpool Dryer - Instructions

Popped the latch out and popped a new one in.

The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your service. You made my life easier.

Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.

Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.

Lifted top of dryer using putty knife. Took front panel off using socket wrench. Slipped drum belt off an took drum out. Vacuumed out entire interior. Replaced rollers an clips and reassembled!! Saved $100!!! Thank you!!

Pulled back panel off, then removed entire front body. Accessed the blower and the lint cover and removed. Removed drum and belt. Removed motor and replaced, reassembled and plugged in and it worked. Thank you

Repair went well your video was a great help. The motor was hard to disconnect from the blower and fan side.The shaft that you hold with the adjustable plier was hard plastic type of material and wanted to keep slipping and the edges wanted to round off and not hold in the adjustable pliers. I had to use a small pipe wrench with teeth to break it loose. The only other problem was the ground screw in the new motor had an odd type of head on it and took a special type of nutdriver attachment to loosen it and attach the ground wire to the new motor.

Completly gutted every part of the machine, to put in the drum support rollers. Really wasn't that difficult. But you will need 2 people. One needs to hold the drum while one replaces the drum roller.

Removed and replaced motor. In the process of removing old motor, the blower wheel had to be unscrewed from the rear shaft of the motor, in order to remove the motor. In my case, the blower wheel had seized up on the rear shaft and could not be unscrewed. It had to be cut off and it also had to be replaced. The dryer now works fine. Tip: I watched an internet video (repairclinic.com)about the procedure before I started. Very helpful!

I removed the back before I relized that the motor was under the drum. I removed the front and the drum and accessed the motor. I used a small flat head screw driver to prythe brackets that held th motor in place. I had a bit of a problem removing the motor from the fan. Then I read the web site and figured out that the treading was a LEFT thread. Still had some problems and ended up removing the pully wheel and using a pipe wrench to get the fan off the motor.

I wish I had taken a picture of the pully and belt to see how it went back together, but it went back easy enough.

Very pleased with my effort and guess I saved about $300 bucks on the repair, and the 2 plus weeks to get the guy to my house.

Remove screws from dryer vent. lift top up: use screw driver to pry up and release top panel its uses a simple catch. Remove wires from door switch. Lift up and remove front panel from clips on side of drier body. IMPORTANT: two people required - Drum will fall if not supported when front panel is removed. Get down in front of machine: one peron holds drum in place an you push up on belt tensioner. Release belt from drive wheel. Remove drum and set aside. Pry off support clip from front of broken support roller. Clean roller shaft (replace if broken). Place new roller on shaft. Replace support clip. Have second person hold drum in place while you re install drive belt (see above). Replace front panel. Re attach wires to door switch. push top panel down (firmly to lock). replace drier screws.
good luck

My dryer is probably more than 20 years old. I know, I know, but I decided to fix it anyway. I followed the same steps as the other posters here. However, I almost never fix anything like this and the dryer is in a small space with only a couple of inches of clearance on either side.
The repair took 10 hours off and on over 2 days. You will definitely need another set of hands at various times like when you are unscrewing the fan from the motor shaft and when you are reinstalling the drum and belt.
Getting the motor mount clips off the frame was a huge pain and getting the motor back in place and the clips on correctly was a 3 hour learning experience. Make sure you have all the wires hooked back up BEFORE you hook up the motor mount clips. When you seat the motor on the mounts the wiring hookups need to be almost on the bottom. Check the instructions drawing for placement.
You don’t actually remove the fan cover you just unscrew the mounting screws and push it to the side.
Re-hooking up the belt and belt tightener is not intuitive but you will eventually figure it out. I found some generic dryer belt installation drawings on the Internet that showed me how to do it.
The photocopied instructions that come with the motor are kind of fuzzy after a few generations of photocopying.
In the end, it worked! It is also much quieter now.

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

The first and best thing I did was watch the instructional video. This was very helpful. I removed the lint trap and two screws, then pried the top off using a putty knife as described in the video. I I disconnected the wiring harness and the two screws holding the front panel, then removed the panel. Next, I removed the belt from the drum and removed the drum. I had a little difficulty removing the clips holding the rollers, but was able to pry them off after a few minutes. I installed the new rollers and reassembled everything. Note: I used the nut driver to push the new clips onto the roller pins. The problem was resolved and the dryer is working fine!

I started by removing the back of the dryer thinking that was the proper procedure. That is where I found the broken belt. After purchasing the belt I found belt replacement instructions on-line. The instructions guide you through simple steps to remove the two screws in the area where the lint filter is on top of the dryer. The top then simply lifts back exposing the drum. Two more screws just inside the top of the front panel and two screws to remove the door switch assembly and your in. That is where I found the bent idler pulley assembly that pops free when the belt breaks. I purchased the part and followed the directions and then re-assembled the dryer. Dryer works like new. The most important thing I learned through this is that I believe I can now fix anything that breaks on my dryer. With the all the information that is available on-line and the easy access to replacement parts dryer repair is really cheap and simple. Makes me wish I had done some troubleshooting on my previous dryer before I replaced it. Also going through the back of the dryer was a waste of time.

Replaced drum support rollers but did not fix problem. Motor was fried! Replaced with used motor. NOTE. Make certain you install motor in the right position or you will find the drum sitting on motor. The guide must be in the 4 o.clock position and then placed in bottom groove for proper alignment of motor to drum. Job was amazingly easy and online instructions were super helpful.