WED6600VU0 Whirlpool Dryer - Instructions

First I pulled the dryer away from the wall and unplugged it. Next I removed the dryer vent hose and threw it away and replaced it with a more rigid metal vent hose. Next, I used a socket wrench to removed the screws holding on the back cover of the dryer. Once the back cover was off it was just a matter of using the socket wrench to removed the bolt holding the sensor in place. After the part was removed I made sure the replacement was orientated in the same way as the original part and then I unplugged the wires from the bad sensor and placed them in the same order on the new part and then I bolted the new sensor back in place. Since the new part has been installed the dryer is working flawlessly and is not turning off mid-cycle like it was. ***Oh, and an important reminder. When you have the back cover pulled off the dryer use a shop vacuum to suck out any dirt and lint in the back of the dryer and make sure you unbolt the metal chute that the dryer lint screen goes into and clean inside the area near the exhaust blower. This is a VERY IMPORTANT part of servicing your dryer and should be done every few months to help avoid the risk of a fire.****

Un plug or remove power before you start. First you would have to remove the rear panel of the dryer. All you need is a quarter inch nut driver. Then look at the bottom right side of the dryer. There you will see the heating duct. At the very bottom is where the element is. There are two screws on both sides( they will all be removed with a quarter inch nutdriver ). After you have removed the four screws holding the element on you will have to remove two wires from the elemet be sure that you mark them and dont mix them up. You will also have to remove the round temperature sensor because you will have to reinstall it on the new element. Then you get new element and reverse the order of my directions. Good luck and be safe ALL WAYS REMOVE POWER BEFORE WORKING ON ELECTRICAL APPLIANCES.

Pulled the dryer away from the wall took back cover off the dryer. Used volt/ohm meter to identify the bad element. Ordered the element it came in two days. 2 screws and 2 wires to plug in and we were back to drying cloths

thought the heating element was bad, once inside the element
looked good, tested continuity , tested good.
further test revealed I only had 110 volts at the wall outlet,traced problem to fuse blown in disconnect box under
the house.
Did not need the heating element.luckily parts select is taking the new element back since I did not use it.
Hope this review helps.

Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.

The repair was really easy and I loved the DIY videos they were great, not many tools needed to do these repairs that was great. The only thing is this didn't solve my issue.

Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.

Removed two screws from lint trap and pried front of top up gently. Top hinges backwards which is convienent. Two more screws take the front off. Removed drum and old parts. Removed rollers etc. Per the instructions. Cleaned inside of unit with a shop vac.

Reassemble unit and test. Nice and quiet again and working well. Great service fro. Partselect.com.

I replaced both the thermal fuse and the thermistor at the same time. That seemed to fix the problem; but after a couple of days the dryer would not start. When pushing the Hold to Start button, the dryer just gave one beep and would not start. I did a resistance test on the old thermal fuse, and it was OK; so I put the old thermal fuse back in and the dryer works. Evidently, it was just the thermistor (thermostat, internal bias) that was broken. Both are very easy to change.

Good

removed old latch with pliers - inserted new latch

I did what any novice would have done. I took the entire thing apart to get to the gas jet. I did not know about the thermal fuse until I got to the schematic behind the timer and controls. I was a tech back in the 70's and 80's and only worked on electric dryers. Back then I would remove the heater core and twist the coils together to save money. So I had no idea how a gas dryer heating unit worked. So now any one that reads this. You do not have to take the dryer completely apart, I did that for all of you. Just replace the thermal fuse on the back of the unit by unplugging that wires and removing the screws! It looks like a long white piece of plastic with 2 wires to it. You will find this under the full metal shield on the back of the unit. This should be about a 1 hour repair at the most!

Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair

I simply removed the rear panal of the dryer. Removed the two wires from the fuse at the rear of the dryer. Attached an OEM meter across the two fuse connections and had no continuity. Ordered a new fuse and recieved it in 2.5 days.Replaced the fuse,reconnected the wires and replaced the rear panal. Started dryer and it now blows hot air and runs like new. I can't say enough about PartSelect. Great diagnosis using their website, the delivery was fast and I recieved the correct part at a good price. Very satisfied, Thanks PartSelect. Fred F

First ordered belt and rollers Noise continued then orders tension roller. Better but still noise. Son thinks may be motor. Repair was easy just followed what you already had on line.