SGQ2170KS0 Westinghouse Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- J Martin from Guerneville, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer just barely got warm
Everything I needed to know was already on your website. Prying off the top of the dryer (with a big screwdriver under the front of the top) was the hardest thing, since I was afraid I would break something. Only then can the front be removed (taking out just 2 phillips screws). The rest is easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jane from blairsville, GA
- Parts Used:
- 134813601
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The door safety or something needed replaced.
I called a wonderful friend who diagnosed the problem; ordered the repair part; and fixed it!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Plymouth, IN
- Parts Used:
- 5303281135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Heat would come on but not stay on.
Flame Sensor didn't fix it but, it was easy to replace. Unplug electric. Lift up the top and remove wires from switch and light switch. Remove screws that hold on the front and remove front panel by lifting up and out. Sensor is on the left side of the burner, held on with just one screw. EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Otsego, MN
- Parts Used:
- 134587700
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer was not drying completly.
I replaced the Control Thermistor (part # PS1149368) by removing the two screws on the bottom of the lower panel below the door. You will see the Control Thermistor just below and to the left of the discharge chute. Remove the two screws holding the Control Thermistor in place. Disconnect the two wire and reconnect to new Control Thermistor. Replace screws in reverse order of above.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Hixson, TN
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Dryer would not lite
Took the coils off and put the new one on thats all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from MILLSBORO, DE
- Parts Used:
- 134197700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner Bad
Ordered part received next day fast shipping was great part in and working thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Wilmington, NC
- Parts Used:
- 134472202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door handle broke on one end
I had to grip the broken piece that was still attached to the screw with a pair of needle nose pliers and then unscrew it from the back side. After taking the screw out of the other end,I just put the new handle on and screwed it in. Very easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Irvine, CA
- Parts Used:
- 137539200
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Error code 66 - door open
Remove 2 screws at the upper rear attached to the top panel. Slide panel rear back and remove. Remove 2 screws attached to the front control panel. Lift panel upward. Remove 4 screws attached to the front panel (2 at the top, under the control panel, two at the very bottom). Lift front panel up and off, and unplug connector to door switch. Remove some more screws on the internal front panel edges, and the front to back brace holding up the control board. Lift panel up and out, and remove the drum, too. Thermal limiter located toward the rear, attached to the heating vent tube. Disconnect and replace. Re-assemble in reverse order.
Was this instruction helpful to you?
Thank you for voting!
Dryer handle broke
With the parts, the repair went extremely quick and is just like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bret from Tampa, FL
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I shut the door too hard, and the old latch fell down into the inside of the dryer.
The new latch easily snapped it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Balsam Lake, WI
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer wouldn't heat
Removed the panel between the dryer and washer. The gas valve was right in front. The wires were in a plug and easy to remove from old part. The solinoid held in place by a clamp with two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joan from Roanoke, AL
- Parts Used:
- 131775600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shreking noise when turning on, then loud noise from dryer, after a few minutes it would not be so loud but louder than normal.
Replaced everything on the dryer till I got the right problem, seriously, I now have a new dryer in an old body, still came out alot cheaper than buying a new one. I listened to every sound on youtube but none sounded like my dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miles from Austin, TX
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer did not stay hot through complete cycle
This repair took about fifteen minutes. I popped the top of the dryer using a flat-blade screwdriver, leaned it back against the back wall, unscrewed two screws holding the front panel, removed the five electrical spade contacts after marking which went where, swung out the panel and lifted it off. After that, it was a simple job to unscrew the plate holding the solenoids in, at the bottom left of the unit. I replaced the solenoids, closed everything up and now the dryer is working better than it has in the last three years, or so. If your dryer is heating sporadically, the odds are 85%, or more, that a solenoid swap-out will correct the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from South Dartmouth, MA
- Parts Used:
- 134472202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken handle
EASiER than pie! Took off broken part, screwed on new part! Voila! Done. As good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from San Angelo, TX
- Parts Used:
- 134472202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer Handle Broken
Washer handle fixed!
Was this instruction helpful to you?
Thank you for voting!