SGR641HQ1 Westinghouse Dryer - Instructions

Romoved front from dryer . Then loosened tub , slid belt on , reached in back and put belt on pulley , turned tub till belt went into place and reassembled dryer all with the help of a 3 year old and an8 year old,so in my oppinion it was one of the easiest fixes i've ever done!

Replaced rear drum bearing, drum support bearing & drum belt. Still very noisy. Will order new motor & see if that does the trick.

1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.

Main problem was the bearing, replaced the belt and felt seal as well
The video instruction was very helpful
Was easy with basic mechanical aptitude
Dryer running great now
All parts from Partselect.com
Have ordered from them before and would order from them again

replaced bearing and shaft new belt and everything works just fine

I took the new door catch out of the packaging and just snapped it in place it was easy peasy and took less time than opening the package

So easy! I ordered the part on the website. Received it 24 hours later. And popped it in place. Good as new.

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.

I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.

I lifted the top at the front edge, slid the top back, disconnected the ground wire connected to the top at the rear edge, just slides off.
Then removed the phillips screws on the inside front edge, only one on each side,near top of dryer disconnect the wiring harness at the right side, cut the nylon tie strap holding harness also.
Tip front panel out a little and lift up, comes right off.
The coils are in plain site on the gas valve, remove the wires, and the two screws holding the bracket that holdes them in place, slide the old ones off and start putting back together.
I also used a vacume and cleaned all the lint and dust off everything I could, including the air intake at the rear of machine, "Peice of Cake"

lacked instructions. Internet yielded a simple paragraph. Scored real bonus when we discovered the lint build up past the internal filter was approaching catastropic level. Replaced the exhaust tube (plastic) with rigid metal and resolved to disassemble and clean dryer on 2 year cycle in future. Kit just isn't complete without detailed instructions. Parts were complete and sufficient. Local codes have eliminated the plactic exhaust tube. Recommend that all old installs refit to rigid or semirigid before the fire happens!

First i replaced the drum bushing on the rear of the drum ,it was definitely bad but noise was still there
Decided it was the blower assy , pulled the dryer out disconnected the power,took off the frt panel with the door, disconnected the wiring to motor remover motor and fan assy, most trouble i had was fan is on motor with reverse threads messed with removing fan until I figured out it was backwards after that removed old fan and housing installed new one ,put dryer back together,started it and only normal noises
Good for another 5 years
Chuck

I recently ordered parts for a gas dryer, Frigidaire GLGQ2152 ES3. When I received an igniter part number PS12585650 order number 14700077, the igniter was broken when I opened the box. I believe what happened is that the new metal bracket was wrapped in the bubble wrap along with the igniter. I called customer service and was setup to return the igniter which I did. Also, I ordered a second igniter. I receive the second one and it wasn't broken and the bracket was outside the bubble wrap during shipment.

As far as the installation of the "replacement" igniter into the gas dryer, I could not find instructions on how to install it. The received igniter is much different than the original. There was a small instruction sheet stating that the new igniter is different but can be installed using the new bracket that came with the igniter. But again there were no instructions on how to do this. It took me great effort to figure out how to do this.

The old igniter had to be removed by removing the old bracket assembly that the igniter was mounted on. The new igniter had to be installed onto the new bracket and then by sliding the new assembly under the old assembly, the screws were reinstalled. Although the holes where the original screws were to be screwed into were too small, they had to be drilled out. There was no hardware (screws) to install the "replacement" igniter onto the shipped bracket.

After much work, I finally got the new igniter installed (without breaking it) with the new bracket and the dryer is back in operation.

Ordered part from partselect.com. Part was back ordered; however they were very proactive in communicating status updates! When it arrived it was simply a matter of removing door using a philips screwdriver, installing the new hinge and presto - job complete! Kudos to partselect.com ??

popped in one in