DG170AXD1 Westinghouse Dryer - Instructions

Followed the video, it was good, the instructor's tips were useful and time saving.

Unplug dryer, remove rear access cover and removed belt from pulley. Remove bottom cover on front of dryer, remove top of dryer, unplug harness to control panel and remove front door assembly. Remove screws from drum to bearing assembly. Removed drum and belt removed bearing assembly by lifting up and out of the bearing socket. Vacuumed all the lint. Removed the bearing socket, installed all parts and covers in reverse order.

It was super easy! I followed the PartSelect video and everything went fine. Getting the drum out of the machine was a bit tricky but once it was out, the rear bearing kit went in without any problems.

This was a stacked washer and dryer combo and is a lot more difficult to repair, requiring a lot more to take apart and put back together.

This video by Steve Ash was spot on . In our case the white rear support bearing had melted and reformed around the shaft, preventing us from being able to pop the drum in the way described in the video. We used pliers to unscrew the screws on the rear clip from the back of the dryer. The rest of it worked exactly as described in the video. Our model was White-Westinghouse DE600ADD1, which is not a model listed on the PartsSelect website. However the part worked very well. The dryer runs really quite now.

The repair was done by my spouse. We replaced the rear drum bearing. We installed with the instructions sent by parts select. They were very accurate. The total repair took about 1 and 1/2 hours that was only because we cleaned out the entire dryer also, by using an air compressor to clean and blow out all the lint built up. This improved drying time and the part stopped the noise. I don't recall exactly what tools were used besides screwdrivers. This was our first time to replace anything in our dryer of 12 years old. I feel that if you follow the instructions that anyone would be able to do this repair. We did the repair in our garage because you need the room to work on it.

I watched the video and the instructions were perfect. The only thing I did differently was I had a second person help me to hold the bearing spring and hold the drum knob in place. I also used the rear access panel to disengage and re-engage the belt because I know I am not good at doing things blindly. You will definitely want to pre-thread the knob assembly before you screw it to the drum. Glad the kit included a bearing because the old one was completely gone. It took me so long because I took the opportunity to vacuum 10 plus years of lint and I was using it as a teaching opportunity. If I have to replace the heating element I think it will be much faster.

the repair when ok the only problem I had was installing the small white plastic piece in the back without losing the ball bearing .and I also vac up everything inside as well lot of lint

i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

The consensus seemed to be that the loud squealing was most likely the rear drum bearing needing to be replaced. Although the repair went very well (great video!), it did not fix the problem. BEFORE you go the route of replacing the rear bearing, first pop up the top and see if a little piece of plastic that is attached to the top middle of the front panel by a screw is rubbing against the drum (you have to have a load going). I removed this part (I could not find it listed on any parts list) and the squealing stopped. I have no idea what the purpose of this part is, except for maybe keeping the drum from dropping too far down if the load is really unbalanced. This plastic part is on the dryer that has the controls on the front (it has the ability to be stackable) and might not be on the other unit that has the controls on the top back. If anyone has posted this as a possible cause of the squealing, I haven't seen it.

First I like fixing things for myself. So I looked the problem up on the internet. Found the repair tech that I needed. The found your parts site. And BOOM. Looked up mt part on your site. Very easy you had everything I needed. And you got it to me quick. THANKS. When the part hit my mailbox. Everything I needed was there. I pulled the plug. Fliped the lid up. Took off the front. Removed belt off the ideler. Removed drum replaced bearing assy. Put it back together. Closed the lid and pluged the unit in. Worked so well I felt like a pro. My wife was tickled pink. Just like a new one. Thanks guys for making me look good and saving me a lot of money. Will use this site again. I give you 2 thumbs up.

I followed the directions sent by you step for step and the rpair was done in no time at all. Had a little trouble with the roller ball installation but figured out how to install it after a couple of tries. Repair was done with minimal use of standard houshold tools.

It was easy, I handed the part to my husband and he did it!!!!!!!!!!!!!!!

Followed video that was provided!! Now I know how to get the top and front of dryer OPEN. Now I can clean interior of dryer ALSO, lots of lent!!

After figuring out how to remove the top, front, and control panel from the Gallery series, which is different than the dryer in the video, the repair was easy. Just followed the rest of the proceedure in the video.