DG170AXH3 Westinghouse Dryer - Instructions

This was a stacked washer and dryer combo and is a lot more difficult to repair, requiring a lot more to take apart and put back together.

purchased bearing kit

This video by Steve Ash was spot on . In our case the white rear support bearing had melted and reformed around the shaft, preventing us from being able to pop the drum in the way described in the video. We used pliers to unscrew the screws on the rear clip from the back of the dryer. The rest of it worked exactly as described in the video. Our model was White-Westinghouse DE600ADD1, which is not a model listed on the PartsSelect website. However the part worked very well. The dryer runs really quite now.

I set up my laptop with the partselect video going. Laid out my tools and the individual parts that were in the kit. I watched the video a segment at a time, performing the tasks in the same manner that the instructor did. All together, the process took less than two hours, I had no questions or difficulties, and the repair process went flawlessly and successfully. I had never done anything more complicated on a dryer than replacing the hose before this. The sense of pride in doing a repair of this level myself, and avoiding paying someone ridiculous fees to do it, is beyond description.

Basically followed the You tube videos on standard, stand alone dryers as mine is a stack-able unit. Allow a lot of room to work. Unplug electricity and or the gas, vent hose and water hoses. Start removing screws as per the video, remove Belt then lift up then out the dryer drum. (The drum drops in from above on the back of the unit)the rest is remove and replace as you go. *TIP... I use my phone to photograph tricky areas so I can review as needed. It was more scary then difficult. You can do it!

The repair went very well.The biggest problem was the spring on the tension roller when putting back together.But it just takes a little bit of patients and it was fine.Works great now.

I followed the instructions in a Youtube video that an individual made with his kids. The only hard part was removing the drum assembly, the rear drum bearing was very difficult to unseat. I had to reattach the front of the dryer to give the drum assembly more support to be able to lift the rear - but overall it was quite easy to figure out disassembly and reassembly of the dryer. There's really not that much to them.

I used the video, and it helped me a lot! I got the drum out, installed the new bearing, greased the new shaft and the receptacle, then I reassembled. When I tested it, mine was still very noisy, so I removed the drum once more and cleaned/added some grease on the tensioner bearing. This was the cause of the noise in my case, but the bearing & housing were nearly shot, so something would have given out very soon. I would suggest to grease the tensioner the first time to save time and effort. (And save some of the grease for the tensioner pulley). SAFETY TIP: there was also a ton of lint that got trapped inside the unit!!! Clean your dryer once per year to prevent it becoming a fire trap!

the repair when ok the only problem I had was installing the small white plastic piece in the back without losing the ball bearing .and I also vac up everything inside as well lot of lint

i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

Replaced rear bearing on back of dryer. Repair cost $20.00 an a little time. Much better then buying a new dryer. It was easy to repair the video instructions were great. I would do it again it needed.

I ordered the rear drum assembly on Monday evening and the part came on Wed at 11 am. I started the repair at 1 and finished at 3. It would have been faster, but my computer kept freezing during the repair video. The video was so easy to follow. I could have used longer arms or a helper, but I managed to get the job done by myself. Needless to say, my husband was thrilled. Great service. Thanks

followed vidio instruction which made it easy

Follow instructions all most to the letter. In video it was stated to get an assistant to hold static / housing retainer in place to start screws. I put it in place and, used Duck Tape to hold it there while i started screws. Thanks for the deal on parts and, video. I would also suggest advising to check the nylon strips on felt at the front top. Mine were worn. But there was enough at the back of nylon to remove and, glue remainder in place almost as good as new. Again! ''THANKS!''

Hired a professional!