DE641ADH2 Westinghouse Dryer - Instructions

Open the back plate. Broken pulley was already out of place. Put the spring on the pulley and placed it. It took me less than 10 min

First of all, I've purchased a belt from local service center that cost me more than $21 (local tax is 8.5%). But, I can not find the idel pulley assembly so I searched on the Internet and ordered from PartSelect.com.

Surprisedly, my order came just one day - they must cross-ship from local distribution that it's even faster than to get those in local stores (driving .. and hope they have what I want ..).

I've replaced the belt 2 days ago - it's easy with 4 screws removed to pull out the front door. The back panel is opened with 2 screws remove, and very easy to replace the pulley.

It's a heavy duty gas dryer made in 1989 and this is the third time I changed the belt and the first time to change a new pulley. I would recommend to change the idle pulley because I may not need to change the belt if I have had replaced it last time. A broken or not functional idle pulley may damage the belt in a short time.

Appliance such as gas dryer like mine will last forever with replaceable belt and pulley. I'm really happy to see a working dryer (almost 20 years old) and my wife is asking a small component for her washer .. that I think I can easily fix that too .. with the help of PartSelect search.

Hope this will help.

John

Removed access door. Disengaged spring, removed old idler. Slipped belt around new idler and motor pulley. Difficulty is putting spring back and inserting idler pulley bracket back in place while there is a lot of tension from the belt. Finally used adjustable wrench as a mini hammer.

Removed small panel at rear of dryer which allowed access to the Idler Pulley asembly. Easily removed, and replaced with new idler assembly. Fed belt onto new pulley and attached tension spring. Actually, this replacement idler pulley assembly is much better than the original. It has a shoulder to allow the belt to "track" better over drum and around motor pulley. Dryer is now extremely quiet, like a new machine. Hope to get another 29 (yes 29) years out of it. Extremely pleased. Doug East Lansing, Michigan

remove the top and front of the dryer, then removed the idler assembly. This enabled me to rimove the belt form the drum and replace it and the idler assembly. Not difficult at all.

removed front of drier , removed rear access panel, replaced the belt. reinstalled front of drier and rear access panel

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

Replaced belt

Had to remove the front of the dryer but installation was quick and easy. An affordable and quick repair.

The first part was the most difficult-opening the front of the dryer cabinet! Once open, the new belt was installed and then the new idler pulley was put in-place. The cabinet was closed-job done.

Removed small panel from back of Dryer,and removed Idler Pulley Assembly. From the front,lifted the top of Dryer to get access to the drum,disconnected the two wires for the Stop switch, removed the four screws, two on each side,and lowered down the front panel. Now,removed old belt and installed new, installed new Idler Pulley Assembly,aligned belt with Pulley.Reassembled the front and the top of the Dryer and I was done.The pulley was squeaking,but a shot of DW40 took care the problem.
Thanks

Domenico Intrieri

unbolted one bolt and replaced old unit with new unit....took only a few minutes. Part was supposed to arrive in 3 days, but arrived next day....thanks very much!

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

put the new part on with ease took 5 min.

The customer had removed the top cover hinges and the rear cover plate to recover the broken belt. I first removed the four screws holding the front panel and tilted it out to allow access for the new belt. The drum dropped about 2-3". Fed the new belt over the drum with the printing'This Side Up' facing me, lifted the drum up as I closed the front cover over the felt on the front rim of the drum. Replace dhtew four screws. Door switch leads were long enough to allow the front cover to tilt forward so did not remove. Next engaged the motor pully and tension pulley, then rotated the drum manually to assure tracking and no twist in the belt. Vacuumed the wall passthrough pipe,the flex vent tubing and the motor compartment of lint. Closed up the back cover and drove the 52 miles back to my shop.