47-2707-23-01 Tappan Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anna from FLORENCE, KY
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Dryer does not start
Followed video instructions, easy installation. Unfortunately it didn't fix the problem. Plan to take back off and check belt, etc before ordering another part.
Was this instruction helpful to you?
Thank you for voting!
dryer was squealing loadly
took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new dryer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from HGHLNDS RANCH, CO
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
load squeal
replaced rear drum bearing kit. Watched video made it real easy. The only problem was getting the belt back on the pulleys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from El Paso, TX
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Squeeky noise every time the dryer ran.
Popped the topped using a putty knife to free two clips in front. Remove two screws now accessible on the front inside panel. Remove two wires to door switch. Remove rear access door, two screws. Remove belt from tensioner in rear and remember or take picture of how it goes. Lift barrel slightly and pivot front panel out of the way. Lift barrel free from ball socket in rear. Lift out from front panel area. R & R kit and put back in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Norwich, CT
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint screen was dilapidated and needed replacement.
I took the new screen out of the box. I removed the old lint screen from the dryer, and I put in the new screen. Real simple!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Genevieve from NORTH ANDOVER, MA
- Parts Used:
- 131658800
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door catch broke and fell into dryer.
All I had to do was pop in the new door catch. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from LANDRUM, SC
- Parts Used:
- 5303281153, 5300622032, 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
drum bearing broke, and heating element was bad
popped the top off dryer, removed the tub . took the screws out of the tub bearing, and put the new one on. replaced the rear bearing holder. filled with greese provided.replaced the heating element, and put the tub back in with the belt around the tub. replaced the lint screen. put the belt around the pulley and replaced the cover. popped the top down.good as new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Philipsburg, MT
- Parts Used:
- 5303281154, 5303212849
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
worn belt and squeaky bearring
remove the top and front of the dryer, then removed the idler assembly. This enabled me to rimove the belt form the drum and replace it and the idler assembly. Not difficult at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Kennewick, WA
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer made a loud squeaking noise was ready to get a new one
I first diagnosed the problem using a Google search. Amazing how many hits I got and after reading a few was pretty certain what the cause was and what parts I probably needed to make the repair.
Some of the articles I read had links or mentioned PartSelect, so I searched for my model # and found the parts I would probably need. Knowing that I could probably get the parts I needed I disassembled the dryer (pretty easy really) and removed the old suspect part. It was devoid of lubricant and the bearing and ball showed some wear so I ordered the Bearing Assembly suggested by PartSelect (the illustrations looked just like my old parts). I left the dryer disassembled while I waited for the part, figuring it would take a week or so to arrive.
Much to my surprise, the part arrived three days later and after cleaning the dryer innards of all collected lint I put it all back together in 30 minutes.
So for a little research, a $30 part, and about an hour of my time, I have a clean and quiet operating dryer. I see no reason I can't get another 10 or so years out of it.
I consider myself a reasonably handy guy but had never worked on a dryer before. I'll be unlikely to ever call a repairman without first doing some investigation and seeing if the parts are available. With the internet and PartSelect I think I could take on a lot of other repairs I'm not familiar with. Thanks for a great outcome this time around.
Kevin
Some of the articles I read had links or mentioned PartSelect, so I searched for my model # and found the parts I would probably need. Knowing that I could probably get the parts I needed I disassembled the dryer (pretty easy really) and removed the old suspect part. It was devoid of lubricant and the bearing and ball showed some wear so I ordered the Bearing Assembly suggested by PartSelect (the illustrations looked just like my old parts). I left the dryer disassembled while I waited for the part, figuring it would take a week or so to arrive.
Much to my surprise, the part arrived three days later and after cleaning the dryer innards of all collected lint I put it all back together in 30 minutes.
So for a little research, a $30 part, and about an hour of my time, I have a clean and quiet operating dryer. I see no reason I can't get another 10 or so years out of it.
I consider myself a reasonably handy guy but had never worked on a dryer before. I'll be unlikely to ever call a repairman without first doing some investigation and seeing if the parts are available. With the internet and PartSelect I think I could take on a lot of other repairs I'm not familiar with. Thanks for a great outcome this time around.
Kevin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George W. from Limon,, CO
- Parts Used:
- 5303931781, 131825900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Support was worn out, tub shaft also.
Removed two screws in the inside of the front after opening the top by releasing the two clips. Front comes off of bottom clips easily. Drum can be removed and repairs made. Takes less than 30 minutes Be sure to remove door switch wire & unplug unit first. Drum belt can be re-installed easily thru the back access panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George W. from Wallkill, NY
- Parts Used:
- 131390300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lint screen had separated from frame letting lint into vent.
New screen and holder came in, removed screws holding the holder in place and reinstalled new one & dropped the screen in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margery from Hartland, ME
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The drum belt was making a squealing noise, and it looked frayed.
After watching the video that explained and showed how to replace the bearing assembly, installation was a breeze. Great company to do business with. Ordered the part and had it in two days, and the dryer was working again asap. Thanks PartSelect
PS this dryer is 23 years old.
PS this dryer is 23 years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin from Hueytown, AL
- Parts Used:
- 5303281154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
belt came off
removed front of drier , removed rear access panel, replaced the belt. reinstalled front of drier and rear access panel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Dothan, AL
- Parts Used:
- 5303281153, 5300622032
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
bearing had worn and heat element broke
pulled dryer apart removed drum replaced bearing ass. and heat element and then put it back together. works great now. no squealing and heating great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nelson from cape canaveral, FL
- Parts Used:
- 5300622032
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
did not dry
unscrewed the front panel,dissconect wiring and unscrew drum , just the 3 center ones do not unscrew the outer screws inside the dryer ,take belt off and pull drum out. unplug old element ,replace heating element. the most difficult part is to replace drum and screws,for best results screw one, turn drum and make the screw in six o clock position with each one so the weight of the drum does not fight you
Was this instruction helpful to you?
Thank you for voting!