TDE336RBW1 Tappan Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Mayfield, KY
- Parts Used:
- 131658800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
put door catch in hole
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from DOVER, NH
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Scraping noise from front of dryer
I had this happen a couple years ago so I knew what to do. The hardest part is getting the old glue off. I did that with some nail polish remover and a paint scraper - probably took 20 minutes just to get the glue off. From there, it's just glue on the new one and slap it back together. In hindsight, however, I would've ordered and installed the lower guide as well and done it all at once.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gordon from creve coeur, IL
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
banging noise
followed vidio instruction which made it easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ernest from Stockholm, NJ
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Loud squealing noise until dryer heated up - then quiet
purchased bearing kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from salem, OR
- Parts Used:
- 5303281153, 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Rear drum bearing kit had sheared off
Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Alto, MI
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Squeak and clothes getting stuck
Just want to say what a great company to order parts from, I ordered the wrong parts by mistake, broke the part trying to install the incorrect part, emailed customer service and they not only gave me credit for the wrong part I ordered but, also for the shipping...I will definitely be ordering again from this company
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donald from belmont, VT
- Parts Used:
- 134120900
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
dryer tripped the circuit breaker
disconnected the dryer; cleaned the duct. I reconnected everything and started it up again and within seconds tripped the breaker.Decided probably the thermal limiter was faulty, so ordered new one from you. After it arrived I watched video, then removed the top and front, pulled drum to give me some workroom, replaced the limiter, reassembled in reverse order.I then reset the breaker, plugged the dryer in. Runs perfect.The drum was a challenge - so I used a wooden wedge to support from the front and opened the 12 by 12 rear port to access and reset the pulley cable assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Flagler Beach, FL
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squealing after dryer running 20 m inutes
Installed Upper Drum Glide. Fixed problem 90%. Sprayed silicone on pads and squeal almost all gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TonyMac from Alamo, TN
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Rear drum bearing failure
Follow instructions all most to the letter. In video it was stated to get an assistant to hold static / housing retainer in place to start screws. I put it in place and, used Duck Tape to hold it there while i started screws. Thanks for the deal on parts and, video. I would also suggest advising to check the nylon strips on felt at the front top. Mine were worn. But there was enough at the back of nylon to remove and, glue remainder in place almost as good as new. Again! ''THANKS!''
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Witly from Wheatley Heights, NY
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The only probelem was to take out the drum, because it was a washer and dryer combo. the dryer was on top, i did not have any room to pull out the drum
I remove the drum, and install the bearing just like the instructions in the video.
Was this instruction helpful to you?
Thank you for voting!