TDG546RBW1 Tappan Dryer - Instructions

UNPLUGGED the dryer!!! Search this site they have instructions for many of the tasks they sell parts for... disconnect the vent hose, removed the access panel for the motor & belt (rear) (1/4 nut driver), slipped the belt off the idler pulley and motor pulley, carefully lifted the front edge of the top panel & rotated it back on the hinges, labeled and removed the door interlock wires (2), removed 4 screws securing the top of the front panel (5/16 nut driver) (magnetic is best), removed a yellow guide also attached to the top of the front support (5/16 nut driver), rotated the top of the front panel clear of the drum opening (while supported) and lifted the front panel off the bottom guides, carefully lifted the back of the drum straight up about an inch while supporting the front of the drum, remove the drum from the opening created by removing the front panel (the belt should come out with the drum, removed the rear parts of the new bearing (atteched to teh back of the dryer) 5/16 nut driver... you will need a helper to catch the ball bearing holder on the exterior back of the dryer in the middle, unscrew the drum half of the bearing assembly from inside the drum (3 phillips head screws). I have done this several years ago and you will be amazed at how much dust and lint there is... CLEAN AND VACUUM EVERYWHERE AND THEN ALL THE PLACES YOU MISSED DONT FORGET THE VENT HOSE. Clean all of the old grease from the back of the drum and dryer. Installation is the reverse of removal. Don't forget the new grease and DON"T loose the cute little ball bearing that comes in the new kit. There are lots of sharp metal edges inside so use caution and hopefully you got a new belt since belt replacement requires all of the same steps except for the actual bearing removal.

I can attest to this system only on my model since this is the second bearing I have done.

Sure beats the cost of a new dryer!!! Thanks PARTS SELECT This is the 5th appliance I have repaired for freinds and family with parts purchased from your site.

There was a gap between the drum and the front opening. So, we opened the top of the dryer using the putty knife. There are two clips once you find them you just have to push back on them to release the top of the dryer. Then there are two screws that hold the front of the dryer on. Once they are removed the front of the dryer just came off. The kit has glue and instructions past that point and I just followed them.

1.Removed access panel on back of machine in order to place a block under the drum(see step 3).2. Removed the top (clips), 3.removed the front panel(clips), block placed under drum earlier prevents drum from tilting and makes removing front panel with door very easy.4. Slipped new belt on. 5.Replaced front panel and removed block under drum. 6. Aligned belt and checked movement of drum, 7. attched belt to pulley on motor and positioned belt tensioner.8. Installed top and access panels.
This repair is very straight forward, block under drum makes things easy, since the drum stays level when the front panel is removed and replaced.

First removed the top of the dryer, then the front of the dryer. Took the plate off the back left of the dryer to disengage the belt off the pulley.
Took the three screws out that hold the drum in place, of course the third screw stripped and had to use a screw remover, which didn't work, but the adjustable pliers did so then lifted the drum out of the plastic reservoir in which the bearing laid. Next unscrewed the two bolts holding the plastic reservoir which also loosened the small metal piece on the back of the dryer where a small bearing is located. Put the new parts in, but instead of putting the larger bearing that fits in the plastic reservoir, I decided to put it on the drum first and guide it into the reservoir all at once, this worked well . Prior to that I put the new plastic piece on the inside and taped it there while holding that piece put the small metal piece with the small bearing on the back of the dryer. I'm sure it is alot easier with two people doing this part, but it worked and I didn't lose the small bearing. Next put the front of the dryer back on and then put the belt back on the pulley, then the top.
It definitely helped immensely to read how someone did this, just follow the instructions given and there you go, no more annoying squeak and also a feeling of accomplishment and thanks to the person who wrote the story on how to do this job, appreciate it.

I First pulled the top panel up and off from the front. Then, on the inside, removed a square head screw from each side holding the front door panel on. I then pulled off the front panel enough to expose the drum. I then removed the old drum glide with a putty knife, and following instructions supplied with the new glide, glued the new glide into place. I then assembled in reverse order of disassembly.

Opened the top of the dryer (no tools needed).
used socket set and removed the two screws (one on each side). unpluged wires from front panel, labled each (good practice).
Pulled open the front panel.
cleaned old felt off all around the front panel. Wiped down everything. while I had it opened, I vaccumed out the dryer underneath.
used glue provided in felt kit and glued new felt where old was.
let dry, put front panel back on ensuring that the felt was between drum and front panel.
put screws back in front panel. closed top.
Let me say that this is the third time I've done this to this dryer as it is about 18 years old.
Until the heating coils go out, this is the cheapest fix there is. :-)

First, I popped the two clips that hold on the top. Then, I removed two screws and unplugged a few wire connectors to remove the front panel. I scraped off the felt, which was rubbing the drum since the white plastic glides had worn completely through. I applied the high-temp adhesive liberally, laid on the new felt, and applied some spring clamps to hold it in place. I removed the small back panel to replace the belt, which was really easy with the dryer apart. The 7-year-old original belt was a little cracked.

First I unplugged the dryer. Then I gently pryed the top of the dryer. This was done from the front using a flat screw driver. Do this gently pushing up on the handle of the tool. It will pop up one side at a time. No need to remove the screws and clips on the the rear top of the dryer. Set the top aside. Then from the inside front of the dryer using a phillips screw driver I removed two screws, one on each side. This allowed me to lift the front of the dryer up and away from the unit, off the two clips on the bottom front of the unit. I set the front cover on top of the dryer. There is no need to disconnect any wires. Next removed the rear vented cover on the back of the dryer so I could acess the belt pullies. From here I pushed the upper left pully to the right to ease belt tension and take the belt off that pully. Slide the belt to the rear of the drum. Next I removed the three screws from the center most part of the inside of the dryer drum. My dryer required the use of a square head driver tool. This allowed me to easily bring the dryer drum out the front of the unit. Set it out of your way. Then I vacuumed the dust out of the dryer. Then I lifted out the metal part that resembles a trailer hitch which had been attached to the dryer drum. Next using a nut driver I removed the two screws which hold the white plastic part of the bearing assembly to the rear of the dryer. That is all the taking apart work.
Putting it all back together was not too difficult. First install the new white plastic part of the bearing assmbly inside the dryer along with the metal part on the outside rear. The little metal ball bearing goes on the OUTSIDE between the little metal part and the rear wall of the dryer. Do not leave it out as it provides electrical grounding between the dryer drum and the body of the dryer. Next attach the new bearing part that looks like a trailer hitch to the rear of the dryer drum. This is the three screw part. Then lift the drum back into the dryer. Do not yet set the drum all the way in. The dryer belt must be looped around the drum. I installed a new belt. If the bearing is worn out it is time for a new belt. The smooth side of the belt goes against the dryer drum. Now apply a generous amout of lubricant to the white plastic cradle which was installed on the back of the dryer and to the ball bearing area. Then the dryer drum may be set into place, that is the trailer hitch part into the white plastic cradle. Now the front of the dryer may be reinstalled. Push up on the inside of the dryer drum to line everything back up. Put the two screws back which hold the dryer front on. Be carefull not to drop them inside. Put the dryer belt back into place on its pullies. It goes on the inside of the left and right pullies and on the outside (bottom) of the pully of the dryer motor. Check for and undo any twists. Plug in and test the dryer. All should be well. Reinstall the rear vented cover. Replace the top, connecting the rear first. Make sure to reattach the green grounding wire. Then push the front of the top down onto its clips. You are done! This took me 1 hour and 10 minutes. It sounds like alot but you can do it! Empower yourself!

Took a putty knife and released top clips. Tipped top back , and took out 4 screws holding front cover in place. Lifted out drum, replaced bearing plate. Removed 2 screws and replaced back panel bearing. Placed drum back in place, installed front panel, snapped top back in place and job was done. Very easy. Took about one hour.

Opened top of dryer with screw driver,removed two screws securing the front door. moved door away from dryer. Removed old felt from door,scraped area to remove old glue and felt. Lightly sanded area to clean. Applied new provided glue and let set for 1 minute. put new felt in place and applied three small clamps to hold in place. Waited 1 hour and reassembled dryer.

lacked instructions. Internet yielded a simple paragraph. Scored real bonus when we discovered the lint build up past the internal filter was approaching catastropic level. Replaced the exhaust tube (plastic) with rigid metal and resolved to disassemble and clean dryer on 2 year cycle in future. Kit just isn't complete without detailed instructions. Parts were complete and sufficient. Local codes have eliminated the plactic exhaust tube. Recommend that all old installs refit to rigid or semirigid before the fire happens!

took apart and replaced parts easy to do but no one in my town can get me parts. thay want 100.00 gust to come out and look at it so found parts online and thats that

First I raised the top of dryer, then removed 2 screws holding the front of dryer to the sides. removed old drum glide using a putty knife and glued new glide in place with glue provided. replaced front and top. The whole job took about 20 minuets and saved me the cost of new dryer

took off face of dryer, removed drum 4 screws removed two srews holding bearing and shaft ,replaced shaft bearing and shaft . Just for preventive maintenance i replaced idleling arm and dryer belt. I lined everything up replaced drum used shop vac to clean lint and dust from all parts replaced face of dryer and boom i got a btand new dryer

Removed access door. Disengaged spring, removed old idler. Slipped belt around new idler and motor pulley. Difficulty is putting spring back and inserting idler pulley bracket back in place while there is a lot of tension from the belt. Finally used adjustable wrench as a mini hammer.