SDG109WF Speed Queen Dryer - Instructions

Replaceing only this item fixed my problem
with front panel removed Ignier would turn on, gas would light, ignitor went out as usual, but gas would shut off after a few minutes and not come back on.
Note gas dryers are supposed to light, heat up, igniter stop flame stop after it gets up to temp, shut off for a while then repeat the process, it would have saved a lot of time researching to have known that earlier.. Take front panel off screws off, take panel off holding the 2 round coils in place, unplug the one with 3 prongs and replace, tested dryer with the panel off and the door closed so there was no suction issue. put panel back on 5 minute fix if you knew what you were doing.

I replaced the dryer coils in 5 minutes!!!! It was so easy! If I called a repair guy, he would have charged me $200. I fixed the problem in 5 minutes, and all it cost me was the price of the coils...$15. Sweet!!! I upgraded the shipping to 2-3day, and the coils arrived the NEXT day. Great experience, and very satisfying to fix my own dryer. The dryer works perfectly now and gets very hot!

I saw some videos to have an idea on Wat to look for,most of them described the sensors and the igniter, but one specific mentioned the coils. I did the testing and because all the components were fine I concluded that the coils was the problem. Went online ordered the parts, 2 days later got them, took of the old ones installed the new ones and the job was done drying perfectly. It cost me only $ 25 bucks and probably 10 or 15 minutes to fix it. Tanks part select You have an excellent service.

super easy 2 screws and my 11 year old son took 5 minutes.

well at first I thought was a sensor so i got it, did not work, second intent fuse end sensor kit, did not work, so I thought must be a valve, so I toke other look up on the price of the valve, then i find a kit to repair that specific problem, so I order it, I got it very quick over night, so I installed in 15 min, and walla!!! did work. Thanks a lot. so if no flame, must be the valves...

took off bottom access panel replaced both electronic coils web site helped diagnose problem

Unplugged dryer, and removed vent hose. Tilted dryer back, unscrewed 2 screws on lower front panel. Removed 2 screws on coil holder (needed a short screwdriver). Unhooked wiring harnesses from coils, and removed coils. everything in reverse for installation.

Used your sites diagnostic questions to determine that the gas coils were the most likely cause for no gas ignition. Ordered parts. Followed general directions from your web site....very helpful. Disconnected electrical chord. Removed lower dryer panel. Removed two bracket screws and bracket that held coiles in place on top of gas valve. Disconnected electrical clips and removed coils.....note that one coil is inverted as compared to the other. Cannot confuse as the electrical connectors are different. Slid on new coils, replaced bracket, carefully replaced screws. As space adjacent to coils is tight, be careful in tightning screws so as to not strip heads. Connected coil electrical clips. Plugged in dryer electrical cord. Tested dryer by starting up. Success, gas ignition. Cleaned out dust/lint on the inside of the dryer cabinet before closing up.

check the coils first. parts shipped to house within 24 hours. 29 bucks with shipping!

First I removed the two screws that hold the front access panel. After taking an ohm reading on the coil I found it was an open coil. I went on line to find out where to get the part. PartSelect web site was very complete when I enter the part number. I was able to make the purchase on line. The part was stock and it arrived in 3 days without any special handling. I then unplugged the solenoid, removed the two screws that hold the coils on. Replaced coil and bracket .Tested the dryer and it was working properly. Installed the front panel. PROJECT COMPLETE!!

I took the front of the dryer off. The two gas valve coils were right in front. Replaced the two terminal gas valve coil and the secondary coil valve three terminal. Cleaned the inside with shop vac and re-installed the front dryer panel.

I took the front dryer panel off by removing 4 screws. I the removed 2 screws from the bracker that secured the 2 valve coils. I unplugged the 2 coils the placed new ones in the exact same position. Fastened the valve coil bracket and replaced the front dryer panel. The dryer worked like new. Thanks!!!

removed cover removed old coils installed
new coils ,test dryer running great .
thanks partselect.

Unscrewed the front and ran the dryer. The heating coil DID get red hot but the gas DID NOT blow out. Unscrewed the cover over the top of the two coils. Disconected the wire. Replaced coil and cover. SUPER EASY. Its the starting and holding coil which lets the gas shoot out onto the heating filament. $75.00 just for the repair man to come out plus parts, plus labor. Probably saved $200+. All the prints of the parts are on the website so you can see what your changing. TRUST ME....DO IT YOURSELF. You'll be glad you did!!

MY issue was the heat would cycle up on a fully cold dryer, but if the Dryer stopped for whatever reason or started a sucessive new load, you'd get no heat. I could leave the dryer unplugged for 30 minutes and it would fire back up with heat but would go out shortly, or if lucky might finsh the load.

Most of the repair avenues point towards the cycling thermostat or the flame sensor.

But It was the gas Coils.

It's Been perfect for couple weeks.

Great Site