NE4813L43738 Speed Queen Dryer - Instructions

used one nut driver, basically took the whole machine apart. took snap ring off the idler shaft, replaced pulley, and put it back together. simple job.

removed the lower cover, tipped the dryer on its back for easier access, unscrewed the 2 mounting screws removed the heating element, installed the thermostat and and high tempt relay on new one replaced the wires reinstalled the new element, very simple

You have to take apart the whole dryer to get to the belt.Nut driver with cordless drill make it go so much faster.Unplug dry, take apart dryer and replace with olr belt with new belt.Takes about 20 minutes to do.plus I took off the two guide wheels on back of cabinet and greased everything.Works like brand new.I had a repair guy tell me I needed a new motor.If you can spin the drum by hand replace belt first.

removed drum and motor and installed new parts. Very fast service on parts. Well be back if needed.

Removed 2 screws on the bottom of front panel of dryer & pulled it off. Next I got down & looked to the back & bottom inside of the dryer. I spyed the heating element,I pulled off the two wires from the thermostats[ orange & black. I removed two screws from the heating element plate & dropped it down & removed it from the dryer. Reverse procedure to reinstall. Will see if we can get another 10 years service out of it.

Removed door and front panel. Removed drum. Removed idler pulley arm and spring. Removed snap ring and pulley from idler pulley arm. Reversed process to re-assemble.

Removed the front dryer panels (lower & upper), front drum support and drum. This gave me easy access to the idler pulley and tension spring. I also took the opportunity to vacuum all of the lent that had collected over the years. After installing the new parts and aligning the belt, I reassembled the panels, plug it in and it worked like a champ! Locating the parts on your website was fast and easy. I appreciate it and thank you.

Took off the two lower front screws, Then the screws to take off the door and frame. Then the lint trap. Finally took out the drum. BOY WAS MY DRYER DIRTY WITH LINT! Vacumned it all out and washed the filter and filter housing with soap. Found out that I needed tension wheel also. Ordered that. Replaced the wheel, that was the hardest part. Need to take off this part like a "spring washer" and put it back on with the new wheel in place. Then placed the belt on the drum, belt on the tension, screwed the drum holder frame on, screwed the door frame on, screwed the lower panel on and it works great. By the way I am a female and if I can do it anyone can.

Disconnect the dryer from the electrical source. Using a nut driver, first remove the 2 screws of the lower panel and release the panel. Next remove 4 screws of the door panel and then remove the electrical connections to the door (6 wires). Remember to mark the wires prior to removing so you will remember were it plugs back in on reassembly. Remove the door panel. Then remove the 2 screws holding the top of the dryer and tilt the top open about 90 degrees to access the tumbler. Remove the belt by sliding off the tumbler. Remove the tumbler. You will then access the pulley. Using a pair of pliers, remove the retaining ring by pulling upwards. Then remove the washer and the pulley. Replace the parts with the new pulley, washer and retaining ring. This time would be a good time to replace the belt too. Thread the belt through the pulley and over the tumbler. Place the top back and screw in place. Reassemble the door wiring and reattach the door with the 4 screws. Reassemble the lower panel and plug the dryer back into the outlet and test. There should be no more noise if the noise is coming from the pulley and loose belt.

remove front panel ,remove top panel,lift drum,slide new belt on to drive motor then idler pulley then put belt over the drum.reassemble in reverse , front panel first

clothes drier didn't work, tore the drier apart, found problem went looking for the part locally, didn't find it, got mad, went on line, found Parts Select, ordered part, part under $20.00 delivered, part delivered, put everything back together , can dry clothes again, didn't have to find $350.00 to go buy a new drier. Merry Christmas!

To start the repair, I removed the two front panels. Disconnecting the wiring to door and light. Next removing dryer drum and drive belt[ allows access to belt tensioner] replace tensioner roller, then reassemble. Dryer works fine

My problem was that my AMANA dryer would not heat. The site suggested testing the two thermostats so I opened the dryer but didn’t follow the instructions in the video tutorial on the site since my AMANA is different. I used a nut driver and needle-nosed pliers for the whole job. Here’s what I did:

1. Unplugged the dryer.

2. Disconnected the exhaust pipe at the dryer.

3. Pulled dryer away from back wall about two feet.

4. Removed the two bottom panel screws (floor level) and removed panel.

5. Removed the two door panel screws and removed door panel by pulling out at the bottom until the two spring clips released from the top panel.

6. Noted the colors of the wires going to the door switch and removed (green, black and white from left to right).

7. Noted the colors of the wires going to the lamp and removed (bottom - black and top - red.)

8. Removed the two top panel screws, lifted up the top panel and leaned it against a support.

9. Removed the four bulkhead screws and carefully lifted up and removed the bulkhead being sure to support the drum. Took note of the belt path around the motor and idler pulleys.

10. Reached under the drum and took the belt off the idler pulley and motor drive pulley.

11. Used the belt to lift and remove the drum through the front opening.

I noticed that the internal vent pipe had become disconnected (which probably caused internal overheating) so I fixed that.

I then removed the wires to the thermostats and tested both for continuity. The limit thermostat was bad. I also saw that the belt was becoming cracked. I ordered a new limit thermostat and belt.

Installation of the new parts was a snap. I removed the old thermostat with the nut driver and replaced with the new one and pushed the wire connectors back on. Replacing the belt was a little trickier but not a problem. (Be sure to route the new belt correctly as noted on Step 9 and place ribbed surface next to drum.)

I closed up the dryer by reversing the opening steps.

Lifted the top of the dryer removed two screws and pulled the front of the Dryer forward. Slipped the new belt over the drum and over the motor pulley.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.

removed the front of dryer panel below the door. Cleaned out all the lint. Pulled two screws with an extended nut driver. slid out the old element. I dentified the part . ordered, when the part came in I put a few simple componets on the new, slid it back in. Turned on the power to make sure it was working then reinstalled the front cover. works fine