NE4613L43728 Speed Queen Dryer - Instructions

disassembled the entire dryer drum and front bulkhead plate. Installed belt and replaced drum on rollers and positioned idler pulley .Video was very helpful in positioning drum and belt onto idler pulley. More trouble with the existing dryer vent replacement after repairs were complete

I totally disassembled the Dryer, and replaced the Guide Rollers, Blower Wheel, Idler Pulley Shaft, Idler Pulley, and Belt.

Unplugged dryer removed the front, removed & marked the wires. Removed the drum & drive belt. Removed the snap ring on front of roller with a pgtai awl.Removed the wheel & worn washers, removed the nut on the back of the roller shaft. reppaced it all in reversed proceedure. Other than a few little scrapes on the knuckles it was Quite easy.

I guessed that a new belt may fix the problem. The repair was nearly as easy as the video suggested. I believe the dryer had been repaired before since there was a circular panel on the side which had been removed. I could reach in through the side to slip the new belt onto the pulley. The new belt now enables the drum to turn even for heavy loads.

The repair went very well. The parts were a perfect fit and arrived earlier than expected.It took a little longer than it should have to do the repair because of my recent surgery I had my 11 year old grandson operating the nut driver taking the dryer apart install the parts then reassemble under my watch full eye. You could say it went so easy a fifth grader could do it.

Unscrewed front panel. Pulled off unbroken wire connecter and popped switch and put new one in. Replaced front panel.

remove front part of the dryer and rise up the top to remove drum to replace the belt. than remove two screws for the heating element piece of cake repair.

Removed the 2 screws from the bottom of the front panel and pulled the cover up and out. Labeled the wires to the light and door switch and disconnected. Lifted the belt tensioner arm and unlooped the belt from it and the motor. Removed the 4 bolts that hold the front drum support on then held the drum up and removed the support. Pulled the drum out slightly and allowed the rear to drop, at this point you can get to the rear rollers without pulling the drum out of the machine. The roller shaft was so tight I had to put a straight-blade bit in a 1/4" socket to get enough torque to break it loose. Make sure to use a large enough driver or you will strip the slot out of the screw. This model had a nut on the back but I was able to just drag my finger against it to get it apart. Removed the washer and roller from the shaft and cleaned the shaft and washer with WD40 before reinstalling with the new roller. Vacuumed all the lint I could get to and reassembled, lift drum, push back, front support, 4 bolts, belt, wires, front panel, 2 screws.

Disconnected dryer from vent and power receptacle, placed dryer on its back and remove the front panel by removing screws along the bottom of the panel and pulling down on the panel. Below the drum the element mounting plate was visible so I removed the sensor and element wires, removed the element mounting screws and pulled the element down and out of its "duct". I installed the new element and replaced the wires and front panel. That's all folks!

The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!

Followed video on PartsSelect website, they made it real easy.

Removed the front panel of the dryer and drum to replace the rollers. You will need a snap ring pliers to remove the locking snap ring holding the rollers, replaced rollers, installed new drum belt and replaced the front dyer panel.
Tested the dryer no more noise.

Thanks

My 11 year old daughter broke the door clasp to the dryer by repeatedly slamming it trying to get it to close. I told her to go down stairs write down the make model and serial number and come back up and find a place to buy it online. I left with instructions not to use the computer for anything else until the part was found. Less then 15 minutes later I came back because I heard giggling. She was chatting but had found an exploded view of the door and the part. She was very pleased with herself! We bought it and it arrived a few days later. I saw the empty box. She had opened it and taken it down and installed it herself. A good lesson, for her and me

Well tried to find this simple part around Columbus and even maytag website no luck.Parts select had it to go and arrived earlier than expected.Fixed it less than 5 minutes works great.taken longer to put the light bulb back in,Really like the accuracy and quick response from parts select.If I had called a service tech probably would have cost $50.00 or more for a part that cost a little over $3.00 and saved this site in case I need to order other parts.Thank you

as described in video. Very well done. Thank you