AEM633 Speed Queen Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from fremont, NH
- Parts Used:
- WPW10116735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
No heat
I dismantled the dryer and replaced the thermostat and the heating element. The online videos are excellent. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Rochester, NY
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Not much heat
Loosened the screws, took out the old one. It shorted out to back. Inserted the new one attached wires, Installed screws and it worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Arlington, MA
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door wouldn't stay closed
I used a screwdriver to pry out the broken door latch and inserted the new one in the same slot. Perfect fit. The picture of the part in the order page was a big help to identify the correct part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ian from Greeley, CO
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door would not stay closed because metal latch piece was gone.
I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bradley from West Olive, MI
- Parts Used:
- WP36701W
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
Pulled the old knob off and replaced with new knob
PartSelect sent me the exact part you can't tell the difference.
PartSelect sent me the exact part you can't tell the difference.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Palisade, CO
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
drum not turning properly
as described in video. Very well done. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Rosholt, SD
- Parts Used:
- WPY54414
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
squeeking noise
used one nut driver, basically took the whole machine apart. took snap ring off the idler shaft, replaced pulley, and put it back together. simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DOUG from GRESHAM, OR
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The dryer wasn't drying quick enough.
removed the lower cover, tipped the dryer on its back for easier access, unscrewed the 2 mounting screws removed the heating element, installed the thermostat and and high tempt relay on new one replaced the wires reinstalled the new element, very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from NEPTUNE, NJ
- Parts Used:
- WP40111201
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Drum would slip and at times not spin
You have to take apart the whole dryer to get to the belt.Nut driver with cordless drill make it go so much faster.Unplug dry, take apart dryer and replace with olr belt with new belt.Takes about 20 minutes to do.plus I took off the two guide wheels on back of cabinet and greased everything.Works like brand new.I had a repair guy tell me I needed a new motor.If you can spin the drum by hand replace belt first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John M from Noblesville, IN
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
no heat
removed the front of dryer panel below the door. Cleaned out all the lint. Pulled two screws with an extended nut driver. slid out the old element. I dentified the part . ordered, when the part came in I put a few simple componets on the new, slid it back in. Turned on the power to make sure it was working then reinstalled the front cover. works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from ROTONDA WEST, FL
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Dryer Would Not Heat
Removed 2 screws on the bottom of front panel of dryer & pulled it off. Next I got down & looked to the back & bottom inside of the dryer. I spyed the heating element,I pulled off the two wires from the thermostats[ orange & black. I removed two screws from the heating element plate & dropped it down & removed it from the dryer. Reverse procedure to reinstall. Will see if we can get another 10 years service out of it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from Charlotte, NC
- Parts Used:
- 56000
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
no heat ... rattle ... no air through vent
Determined no air flow or heat through system even though dryer spun and timer worked. Ouside vent dispelled no air. Opened dryer panel.
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !
Blower wheel/fan broken off from shaft. Googled appliance parts ... found ... Partselect .... keyed in mfg, model number ... schematics available ... found part ... ordered ... received in two days ... installed ... reassembled. Working fine ! $ 30.00 compared to buying new dryer ! This was a refreshing and rewarding repair. If it could always be this smooth !!! Great resource ... PARTSELECT !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- april from lexinton, KY
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dryer not heating up
removed old element, relaced with new element , thermostat dryer works better than it has in along time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maurice from East Falmouth, MA
- Parts Used:
- WPY54414, WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken belt on drum
removed front of dryer, replaced old pully and put on new belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRED from ELK MOUND, WI
- Parts Used:
- WPW10116735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Dryer would overheat at all temperature settings
replaced the limit thermostat,thermal fuse, and cycling thermostat. Bingo. Problem solved. Noticed that the back of cycling thermostat had a buildup of lint and I'm wondering if that acted as insulation and caused a wrong reading of temperature. Did not have to disassemble dryer as I could reach all parts with lower front panel removed. To make it easer to install new parts with one hand I lightly hot glued the screws through the new parts and taped the upper portion of new part to bulkhead. With everything lined up and no need to hold the screws I was able to attach using one hand. It was a reach but easily done.
Was this instruction helpful to you?
Thank you for voting!