LES19AW (PLES19AW) Speed Queen Dryer - Instructions

unplug appliance.removed 2 screws @ the rear of dryer top to tip lid back. unplugged the door switch wires.took out 3 philip screws that hold lint screen to inside of drum.removed 2 screws @ dryer front top. lifted dryer front panel off. the drum was now loose. slipped off old belt - replaced with new. set drum back into place. made sure new belt was on motor pulley & behind tensioner pulley arm. replace & reconnect items in reverse order. plug back in & test. after seeing the wear on the plastic tensioner pulley i regret not ordering that part for replacement also.

remove bottom two screws on lower front panel, remove panel. remove two screws on lower portion of door panel, pull bottom panel towards yourself to release pins at the top. Disconnect wiring for light and door switch (make sure to note what wires go where. Complete removal of front door panel. Remove 4 screws holding cylinder frame in place, lift to remove. remove remnants of old felt seal, use rotary tool to remove excess glue, etc. apply glue (used rubberized gorilla super glue), apply felt seal - allow glue to set up. reinstall in reverse direction from removal. Be sure to use glue as there are no clips or other retaining pieces for the new felt and it will not hold in place. overall pretty easy.

Removed the two nuts at the bottom of the dryer front to be able to move the front piece. Removed three screws holding the vent assembly in place. Removed vent assembly, replaced with new part and replaced screws and nuts.

unpluged the dryer,and removed the top.
took the front of the dryer off,release the belt and removed the drum.
unbolted the idler lever.

then I put it back together.
the bolt that holds the idler lever will be a little hard to replace for some.

Early in the life of my dryer, the Cylinder Seal came out. For the past two years I put off buying the part. When it came in, I p[opped the top of the dryer, removed the two screws holding on the front panel, and pulled the Cylinder of the back wall of the dryer. I then placed the seal in the right spot, glued it down and reassembled. About Fifteen minutes of work and a cheap part, and now my dryer dries a l;oad of clothes in an hour instead of three.

I first unpluged the dryer. Then I
Removed two screws and removed bottom cover, Then removed the door assembly.Here I had to unplug the light and door switches. I then removed the four screws that holds the tub mount in place, Then I removed the eight screws that hold the blower cover in place, then removed the blower. replaced blower and reassembled in reverse. I started the dryer and it worked fine.

removed the bottom panel. then the door. unscrewed the 4 screws, removed duct and replaced. parts came fast and fit just right! no issues at all! I recomend Parts select as an appliance vendor for parts.

No problem

Ordered the part, you made it so easy. Received it in two days, very fast, by regular mail. Perfect fit. Pulled out the old broken one and put in the new one!

Ordered the part online and I had it the next day. Installed the knob and voila... job done.

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

I took out the old worn out part and replaced with the one I order.

My son will discribe how he did the repair.
First I opened the top, then I removed the front with a 1/4 inch ratchet and socket. I took the cover off the blower housing with a nut driver. Used the appropriate socket and a 1/2 inch ratchet, and an adjustable wrench to hold the motor shaft and removed the Blower wheel. I replaced the broken Blower Wheel and put all it back together.
Our dryer is now working great and there are no unwanted sounds emanating from within. We are very happy with PartSelects promptness and that we recieved the correct part as ordered. PartSelect website was easy to navigate. We plan if the need arises to do so again in the future.
Thankyou Frank and Rodney

First unplug the dryer,then remove the front bottom panel. With your 5/16 nut driver reach to the rear of the vent tube under the dryer and remove the lone screw that holds the tube in place. Lean the dryer forward and remove the tube from the rear of the dryer,this will allow you to see and reach the idler wheel from the front. Release the belt,feel for the clip that holds the wheel in place on the opposite side of the front,with your thumb nail or something else if preferred pry out on one side of the clip until it pops off. Slide the wheel off being careful not to lose the washer,slide the new wheel on and replace the clip. Put the belt back on replace the tube,which is actually the toughest part because you have to find the hole for the lone screw as you can't see it,but with a little patience it is easily enough done. Put the vent hose back on replace the front panel and plug it in and go!!it took me 30 min. Alittle tough to feel for some of the parts,but really much easier than you would think.