AE5413 Speed Queen Dryer - Instructions

remove the housing under the dryer door. take out the lint trap. I took the whole bottom off the dryer to easily get to the tensioner pully. I then loosened the tub and slid off the old belt and replaced it.

used one nut driver, basically took the whole machine apart. took snap ring off the idler shaft, replaced pulley, and put it back together. simple job.

removed the lower cover, tipped the dryer on its back for easier access, unscrewed the 2 mounting screws removed the heating element, installed the thermostat and and high tempt relay on new one replaced the wires reinstalled the new element, very simple

Removed door and front panel. Removed drum. Removed idler pulley arm and spring. Removed snap ring and pulley from idler pulley arm. Reversed process to re-assemble.

Popped in the new part. Really! That easy!

remove front panel ,remove top panel,lift drum,slide new belt on to drive motor then idler pulley then put belt over the drum.reassemble in reverse , front panel first

Disconnect the dryer from the electrical source. Using a nut driver, first remove the 2 screws of the lower panel and release the panel. Next remove 4 screws of the door panel and then remove the electrical connections to the door (6 wires). Remember to mark the wires prior to removing so you will remember were it plugs back in on reassembly. Remove the door panel. Then remove the 2 screws holding the top of the dryer and tilt the top open about 90 degrees to access the tumbler. Remove the belt by sliding off the tumbler. Remove the tumbler. You will then access the pulley. Using a pair of pliers, remove the retaining ring by pulling upwards. Then remove the washer and the pulley. Replace the parts with the new pulley, washer and retaining ring. This time would be a good time to replace the belt too. Thread the belt through the pulley and over the tumbler. Place the top back and screw in place. Reassemble the door wiring and reattach the door with the 4 screws. Reassemble the lower panel and plug the dryer back into the outlet and test. There should be no more noise if the noise is coming from the pulley and loose belt.

I followed the belt replacement video and voila, the job was done!

removed bottom panel.Has 2 screws on bottom.take belt off of idler. take 2 screws out of motor base.turn motor sideways& remove bolt from arm that holds idler. remove snapring holding idler. replace pully & reassemble in reverse. Thank You Partselect for prompt shipping. A+ Rating

The first time, I inserted the belt the wrong way. The drum turns a little bit then stops. The manufacturer does not give any instructions or drawings on their website on that particular model, only drawing of parts.I called the technical support department and they told me to call different telephone numbers in my area and repair technicians. Still no schematic and instructions.
The solution: I took the broken belt, put around the drum, measured it, the remaining slack, did some trial and error around the motor axle and the pulley.
Placed a 2 X 4 piece of wood to hold the tension of the pulley. With the belt around the drum, carefully inserted the drum downward. placed the belt starting from the left side of the drum to the bottom of the motor axle, around it then to the bottom of the tension pulley, then towards the right side of the drum.
Lift the drum to its proper position, horizontal. Remove the piece of wood. Turn the drum manually so it moves freely. check the belt moving around the axle and the pulley. Install back the panels and screws tightened. Test and observe a few drying runs.

This would be an easy job, if I were to do it again.

I needed to download a manual only to get ACCESS to the machine. Removing the outside lag bolts did NOT provide access.

They had hidden clips that were ENTIRELY invisible from the outside. I believe this was done deliberately, to prevent those who don't know the specifics about this machine from gaining access.

It's an easy job, once you know the idiosyncracies of the construction of the machine. It's a major pain in the ass if you don't, even if you are used to replacing belts in other dryers.

Having done it once, the next time I could do it in under 20% of the time it took me the first time.

as described in video. Very well done. Thank you

clothes drier didn't work, tore the drier apart, found problem went looking for the part locally, didn't find it, got mad, went on line, found Parts Select, ordered part, part under $20.00 delivered, part delivered, put everything back together , can dry clothes again, didn't have to find $350.00 to go buy a new drier. Merry Christmas!

To start the repair, I removed the two front panels. Disconnecting the wiring to door and light. Next removing dryer drum and drive belt[ allows access to belt tensioner] replace tensioner roller, then reassemble. Dryer works fine

Lifted the top of the dryer removed two screws and pulled the front of the Dryer forward. Slipped the new belt over the drum and over the motor pulley.
Pushed the front back in place and snapped the top of the dryer down and the job was complete.
I thought the part would take three days to get here.
It was delivered the day after I ordered it.