ADG4BRGS111TWAH Speed Queen Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ramon from BROOKLYN, NY
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
dryer not heating
replace two heating coils. Dryer working find.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Springfiled, OH
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would light for 30 secs. & flame would go out
Checked ignitor it was working ok, disconnected 3 pronged coil and disconnected 2 pronged coil using multi tester checked continuity on both coils both tested 0,with help of operator ordered M Series new style coil kit. When parts arrived installed coils attached wire harnesses installed bracket and 2 screws that secures coils. Started dryer it worked and stayed working who needs the Maytag Repair Man probably saved about 200.00 between service call and markup on coils. Thanks Virtual Repairman
Was this instruction helpful to you?
Thank you for voting!
no flame on burner after initial ignite
I shut off the power supply (pulled plug) . Opened the front access door on bottom of dryer, The two coils sat on top of burner unit, with a plate and 2 Phillip head screws securing them. .I used a small set of pliers to pull the terminals off, then I used a short Phillip head screw driver due to the proximity of the dryer drum close by. The coils slide off, slide the new ones on, re secure the plate with screws, reconnect the terminals, plug in the power cord and away you are for a fraction of the cost.
Was this instruction helpful to you?
Thank you for voting!
dryer not heating( after replacing the high temp. thermostat
i removed the door and front panel then removed the two screws holding the coil bracket,disconnected the two wires on coils,set new coils in place and reversed the above process
Was this instruction helpful to you?
Thank you for voting!
The gas would not ignite.
First we removed the front panel then the door. Removed the old coils and put in the new coils, oh yeah don't forget to disconnect the power supply first. Sure enough that was all it took and it runs great. You really can fix your own appliance if you take the time to do some research.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from RIVERSIDE, CA
- Parts Used:
- 279834
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Igniter works, valves open, gas Ignitestation then shuts off
All the videos said the same thing. If the Igniter works and the gas ignites bit shuts off soon after that, then the coils are bad. I bought the coils and it didn't fix the problem. My bad, I should have put my meter on it to test it before I bought the part and waited a week to get the coils. Now I'm in the process of illuminating the sensors. I will figure it out. Make sure you use the meter. It will save you the headaches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Livermore, CA
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
No Heat from dyer
Well, this is quite easy really. I found the problem after plucking and chucking a few parts but it was finally the igniter that was the problem. After taking the front section panel off to access the components, take the time to unscrew the igniter and see if it is cracked. That is what happened to my unit. I replaced to the new M series coils as well but the issue was the igniter. Look very carefully for a crack, the one on my unit was very small. You can ohm it out with a meter and if it reads open it is cracked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Plainfield, IN
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Gas dryer would not ignite.
I removed two wires from the coil valves. Then I removed two screws from the bracket that holds the coil valves in place. I removed the faulty coil valves and replaced them with the new ones. Put the bracket back on and replaced the two screws and wires. It took almost 5 minutes. The dryer is like new once again.
Was this instruction helpful to you?
Thank you for voting!
igniter wold come on for a second then shut off no flame
removed the two screws that hold the coils in place pulled the coils terminal connections off removed and replaced with new coils reattached quick disconnect terminals dryer now works better than when it was new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Glendale, CA
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dryer flame would light then would not ignite again
I used a socket to take of the front cover. I used a screwdriver to remove the two screws that held the coils in place. Replaced the coils and put everything backs together. Piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Westfield, IN
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Intermittent Heat
1. Unplugged from wall, turned off gas and opened top cover. 2. Removed two wire clips for door switch and unscrewed front cover (2 screws inside). 3. Removed front cover and moved to side. 4. Unplugged connectors from coils. 5. Unscrewed coil screws. 6. Replaced coils and tightened screws. 7. Replaced front cover, tightened screws and reinstalled wire clips. 8. Closed top cover, turned on gas and plugged in power. 9. Dryer fired right up and made heat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sung won from flushing, NY
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The dryer was not thoroughly drying clothes, even after 2 hours.
The front panel was taken out and the parts were replaced. After the replacement, the drying time went back to the original 30-40 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Bel Air, MD
- Parts Used:
- WPW10121334
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Clanging of dryer when rolling
Followed video on PartsSelect website, they made it real easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from OAKLAND, NJ
- Parts Used:
- 279834
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
Gas valve coils need replacing
Gas valve coils need replacing I followed parts select.com video on YouTube and had no problem. It went exactly as the video followed parts select.com video on YouTube and had no problem. It went exactly as the videos showed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Chicago, IL
- Parts Used:
- 279834
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
dryer heat won't stay on
bought the new coil valves changed out new for old, presto dryer works now
Was this instruction helpful to you?
Thank you for voting!