ASEE8AGW173TW01 Speed Queen Dryer - Instructions

Removed 2 screws on the bottom of front panel of dryer & pulled it off. Next I got down & looked to the back & bottom inside of the dryer. I spyed the heating element,I pulled off the two wires from the thermostats[ orange & black. I removed two screws from the heating element plate & dropped it down & removed it from the dryer. Reverse procedure to reinstall. Will see if we can get another 10 years service out of it.

First I removed the two screws that hold the front access panel. After taking an ohm reading on the coil I found it was an open coil. I went on line to find out where to get the part. PartSelect web site was very complete when I enter the part number. I was able to make the purchase on line. The part was stock and it arrived in 3 days without any special handling. I then unplugged the solenoid, removed the two screws that hold the coils on. Replaced coil and bracket .Tested the dryer and it was working properly. Installed the front panel. PROJECT COMPLETE!!

MY issue was the heat would cycle up on a fully cold dryer, but if the Dryer stopped for whatever reason or started a sucessive new load, you'd get no heat. I could leave the dryer unplugged for 30 minutes and it would fire back up with heat but would go out shortly, or if lucky might finsh the load.

Most of the repair avenues point towards the cycling thermostat or the flame sensor.

But It was the gas Coils.

It's Been perfect for couple weeks.

Great Site

UNPLUG Drier
Remove bottom panel 2 screw
Remove 2 connector to coil
remove 2 screws
lift off cover
lift coil s
reverse steps

Unscrewed the front and ran the dryer. The heating coil DID get red hot but the gas DID NOT blow out. Unscrewed the cover over the top of the two coils. Disconected the wire. Replaced coil and cover. SUPER EASY. Its the starting and holding coil which lets the gas shoot out onto the heating filament. $75.00 just for the repair man to come out plus parts, plus labor. Probably saved $200+. All the prints of the parts are on the website so you can see what your changing. TRUST ME....DO IT YOURSELF. You'll be glad you did!!

removed old element, relaced with new element , thermostat dryer works better than it has in along time

I took the front dryer panel off by removing 4 screws. I the removed 2 screws from the bracker that secured the 2 valve coils. I unplugged the 2 coils the placed new ones in the exact same position. Fastened the valve coil bracket and replaced the front dryer panel. The dryer worked like new. Thanks!!!

removed cover removed old coils installed
new coils ,test dryer running great .
thanks partselect.

I took the front of the dryer off. The two gas valve coils were right in front. Replaced the two terminal gas valve coil and the secondary coil valve three terminal. Cleaned the inside with shop vac and re-installed the front dryer panel.

The first thing to do is to check to be sure the vent is clear. The easiest way to see if this is the problem is to pull the dryed away from the vent and let it vent into the room. Once you have determined that the vent is not the issue, take the front cover off and see what is going on on the inside. To remove the front cover first remove the 4 screws on the inside of the upper cabinet to take off the control panel, I was able to gain access to the screws under the front of the control panel that hold the front cover in place. A couple of electrical connectors later the cover is removed. The coils are easily accessed from in front of the burner by removing the 2 screws that hold the small silver cover over the coil. Once the cover is removed, the coils slide off a short shaft and you can replace the coil by swapping the apporpriate electrical connector for the coil being replaced. The coils are alligned with a small white pin so you can't get it wrong. Replace the covers and fire away.

This repair is easy and saves you a lot of money. This is a great web site, easy to identify the parts you need and the delivery is very fast. Nice Job!!!

The diagrams listed online gave me a the information needed to trouble-shoot which part could be broken. It only took two tries to see which part was out but was significantly cheaper than a repairman. The expediant delivery on parts made down-time a minimal. Very pleased with results.

After researching the problem, I thought the solution would be to replace the two terminal coil valve, but wasn't 100% sure it wasn't the 3 terminal coil, so I bought both. the dryer is 13 years old so I thought it deserved new coils. My husband was away for the week and I had about 10 loads of laundry to do. I dreaded the thought of going to the laundromat, so I went ahead and ordered the parts, thinking I would call a handyman to install them once they arrived. However, I found a Youtube video showing exactly what I had to do and thought it looked easy enough. I unplugged the machine, removed the front hatch and the 2 small screws holding the coils in place. I unplugged the old coils, used a vacuum to remove the dust in the area and installed the new coils. I popped them back into place, screwed them in, replaced the hatch, plugged the machine in, and VOILA!!!! A dryer that heats!!!!

Unplugged the dryer from the wall. Removed the front lower cover. Removed the two screws for the bracket that holds down the coils. Unplugged the coils and swapped them out. Reassembled everything in reverse order. Plugged the dryer back in and started it. It's as good as new.

Found symptoms on Part Select website and confirmed that the problem was the coils. It was extremely easy to find and the site saved me hundreds of dollars on a repairman, labor costs and marked up parts. It literally took about 5 minutes to repair. Awesome site!!Thank You

1)Pulled electrical connectors off each of two gas valve coils. 2)Removed two Phillips screws and removed coil retainer bracket. 3)Lifted off two old coils and replaced with two new coils. 4)Replaced coil retainer bracket and plugged back connector on each coil; total coil replacement time is less than two minutes. 5)Confirmed gas valve opens and gas ignites every time over a two day test period. 6)Re-installed door. Wife Happy. We spent under $20 for 'M' series new style coil kit; and the $7 shipping got it here in two days. What a deal! Terry Rahmer 8.24.2012