ASEE8AGW173TW01 Speed Queen Dryer - Instructions

i read some of previous customer problems and fixes pulled the front cover off found coil's location when i turned on drier you could see the ignitor getv hot but burner would not ignite unless i put a little pressure on secondary coil when i let go of coil flame would go out. ordered 'M' series new style coil kit came in in about three days installed parts drier workng good i would reuse parts select agian thanks

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

Checked out the coil seemed ok. So I replaced the radiant flame sensor. No change. Then I replaced the High limit sensor still the heat was not staying on. I read some were in the troubleshooting guide that the coil can test good, but can still malfunction. So that was it new coil fix it, works like a new Dryer again.

I took off two screws on the front panel and removed it. I then located the old element inside at the back, left side of the dryer. I removed the two screws holding it in and then transfered the wires to the new element. My dryer works better than it ever did before. Thanks,

Thanks to reports from others, I concluded that most likely the gas ignition coils (one or both) were no longer functioning properly. I replaced both with the 'M' Series New Style Coil Kit which is about 1/2 the price of either coil individually -- yes,true,go figure! The actual replacement took only about 10 minutes. What was most difficult and took the most time was the removal of the front panel of the cabinet -- this was difficult only because there were no instructions in my owner's manual (or any other source I could find) and it took me awhile to figure it out. Now I could do the whole job in about 20 minutes! The detailed instructions from others as to the process of replacing the coils was invaluable -- I don't know if I would have been able to figure that out on my own. But most important was the information that enabled me to diagnose the problem in the first place. Thank you, all you previous comment contributors.

Disconnect power and pulled the lower front panel off unit (2 screws).
I used a ohm meter and found heater coil open. Ordered correct part online (easy to find it on the web site).
Three days later, new part in hand I unplugged the failed unit's wiring and removed the heating unit (2 screws). Installed the new part, connected wires and reinstalled the four screws.
Engaged power and turned the dryer on. Vent pie had heat, so placed wet clothes in unit and ran a dryer cycle. Works like new. Cost was about $65.00 versus the $500.00 for a new dryer.

did basic diagnostics to narrow down the problem to be likely one of the three parts include w/ the kit. removed front panel and confirmed that part looked like the one on the web page. part arrived 3 business days after ordering.
used nutdriver to remove two screws holding old part in place. pulled old part out still attached to wiring harness and assembled new part and attached wires the same way as the old part. installed new part, plugged in dryer and confirmed that it was heating. replaced front pannel and dryer is now working as well as ever. hardest part was reaching to the back of the dryer from the front while lying on the floor. total cost was cheaper than a service call, let alone paying for parts and labor from a service tech.

Well first of all you get to the back of the dryer from the FRONT.. after lower panel was removed location of the heating element was right in front of you. Two 7/16 sheet metal screws hold the heating element in place very easy to remove.. upon removal you will have plenty of room to pull element out and switch out the wires you need to do.. Upon examination I think my trouble was a high limit fuse that burned out, so I propably did'nt need to buy the whole element ( you might want to check that first it is the ceramic one ) cleaned everything out and dryer is as good as new Good luck

First we removed the front panel then the door. Removed the old coils and put in the new coils, oh yeah don't forget to disconnect the power supply first. Sure enough that was all it took and it runs great. You really can fix your own appliance if you take the time to do some research.

Checked ignitor it was working ok, disconnected 3 pronged coil and disconnected 2 pronged coil using multi tester checked continuity on both coils both tested 0,with help of operator ordered M Series new style coil kit. When parts arrived installed coils attached wire harnesses installed bracket and 2 screws that secures coils. Started dryer it worked and stayed working who needs the Maytag Repair Man probably saved about 200.00 between service call and markup on coils. Thanks Virtual Repairman

Well, this is quite easy really. I found the problem after plucking and chucking a few parts but it was finally the igniter that was the problem. After taking the front section panel off to access the components, take the time to unscrew the igniter and see if it is cracked. That is what happened to my unit. I replaced to the new M series coils as well but the issue was the igniter. Look very carefully for a crack, the one on my unit was very small. You can ohm it out with a meter and if it reads open it is cracked.

I removed two wires from the coil valves. Then I removed two screws from the bracket that holds the coil valves in place. I removed the faulty coil valves and replaced them with the new ones. Put the bracket back on and replaced the two screws and wires. It took almost 5 minutes. The dryer is like new once again.

removed the two screws that hold the coils in place pulled the coils terminal connections off removed and replaced with new coils reattached quick disconnect terminals dryer now works better than when it was new

I used a socket to take of the front cover. I used a screwdriver to remove the two screws that held the coils in place. Replaced the coils and put everything backs together. Piece of cake!

All the videos said the same thing. If the Igniter works and the gas ignites bit shuts off soon after that, then the coils are bad. I bought the coils and it didn't fix the problem. My bad, I should have put my meter on it to test it before I bought the part and waited a week to get the coils. Now I'm in the process of illuminating the sensors. I will figure it out. Make sure you use the meter. It will save you the headaches.