AEM677W2PAEM677W2 Speed Queen Dryer - Instructions

Had to figure out how to open the dryer - bottom screws in front and work up, removed the drum and found the fan blade was broken. Had some difficulty removing the fanblade from the motor shaft but after that the new one was easy to install. I did need help to place the belt and drum back into place. as one person has to hold the belts on the pulley while the other adjusts the belt while putting the drum back into place.

At first i thought i had to buy new dryer, because i did not know what to do.I said, i never done this kind of repair before, well i put everything apart and notice that the idler pulley was worn out, then i said this is something that i can fix it if i get the part. I made several calls and couldn't find it. so went in internet and found it with you.

Simple,I unplugged the dryer and took off the panel located below the dryer door. To do that unscrewed 2 small screws on the underside of the panel. Once that was off I used a flashlight to locate the heating element which was in the rear of my Amana. Using a socket attached to a screw driver I turned 4 screws out of the element and it was free. I brought the element closer and compared it with the new element and made note of the wire pattern. I plugged in the new wires I received in the box into the new unit and then one by one unhooked the wire leads coming out of the dryer. I reversed the above there it was...maybe 30 minutes!

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.

Replaced coils on gas valve.

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

First I unpluged the dryer, removed the two screws from the bottom access panel. I used a small socket to remove the screws securing the limit stat to the burner chamber, nut driver was too long.
I installed the new limit stat with the two screws and attached the two leads. Plugged in the dryer and conducted a test run, burner ignited. I turned the dryer off and replaced the access panel.

1.Unplug unit
(gas model, did not shut off)
2. Remove bottom front panel-2bolts
3 Remove main front panel-2 bolts (no need to remove door)
4. Make note of wire colors on door switch and light, disconnect
5. Remove 3 screws that hold air duct assembly(that lint filter rests in) then set main front panel aside
6. Remove lower air duct (to blower motor)-3 bolts
7. Lift and tilt-up top lid/panel of dryer and wedge wood or ? (this will give you easy access and better light)
8. Reach back behind motor to move idler pulley and remove belt from motor & idler pulley
9. Remove 4 bolts and lift up and out front bulkhead frame that holds drum in place
10. Slowly pull straight out & slightly up entire drum
11. Remove circlip/retaining ring, washer, roller, washer and shaft assembly.
12. Vacuum entire unit
13. Light lubricant on shaft when reinstall in reverse order.

Snap ring pliers and a mental note of how the belt is routed on idler will prevent unwanted profanity.
This is an inferior/substandard unit before Maytag bought them. Spend the money and replace both rollers with new shafts (about 50.00). I have spent over 140.00 in parts to keep this unit running (less than 8 years old). So do the math before you start pouring money into this model.

Removed the top and opened the front cover had to use a 1/4 inch socket with a 5/16 and a short adapter to remove the sensors. The push on wire clips were very hard to remove so I used a pick to open them a little. Before replacing the wires I sqeezed them back to normal so they would not vibrate off. Not much space to work if you don't have the tools but it could be done by removing the gas tube and the heat tube but it will take more time. We have put perhaps 30 loads into the dryer this week and its working better than ever. The Thermostat limit switch was blown used a voltmeter to test for continuity. and I accidentally broke the ends of the high limit switch off while testing due to the tight clips. Maytag sure cant make them like they used to but glad I found a place to get the parts which are easy to replace and the instructions are great to figure out the problem.

Replaced glides and assy idler pulley cleaned all parts fron dust and debree, vaciumed heating eliment to remove all excess lint and wool to make sure I did'nt have a fire in the lower unit.
Job was'nt all that hard just have to watch what you're doing.

Removed all of the front outer bolts holding in the lower plate, front door assembly, drum outer frame and drum. While removing the outer sheel there are colored wire connections that activate the linterior light and door sensors in which I marked the interior sheel with a marker so I knew which wire went where. Before removing the drum I drew a sketch on how the belt is ran thru the pullys and around the drum, so I would have no problem reinstaLLING IT.The rooler bracket was easily removed with a socket wrench and the retaining wring was pried with a pliers. Reinstallation of the shaft, roller and ring were as simple as removal. I then cleaned the entire interior and lint basket for optimal performance. The most difficult part is pulling the belt back around the drum, but still not very difficult. Finally I reattached nall removed parts as they were removed and I now have a like new dryer for about $20.00 vs, buying anew one or repair fees costing Hundred$ OF DOLLERS.
Thanks Partsselect.com Again!

The belt tensioner was the problem and the belt had very fine cracks in it so I ordered four parts: the belt tensioner, belt and the two drum rollers. I had to work to clean the fan and the LARGE dust bunnies. I'm writing this to encourage others to consider installing new duct work, mine was becoming a fire hazard. At a minimum clean all the duct work. Your dryer will work so much better. Thank you for your printable help!??

Followed the recommended repair under noisy machine, replacing the 3 recommended parts. The 10 minute video was extremely helpful. Important note: there are two(2) drum support rollers. Also, you definitely need very small C ring pliers and don't forget to label all wires before disconnecting.

Changed, got in aimed wrong direction-best to take a digital photo before you disassemble. Overtightened bolt and nut in assembly, it seized. Attempted to drill/grind it off, should have removed motor. Drill skipped up into motor windings. Could have replaced dryer, decided not, fixed by ordering motor, mount, nut and bolt and new belt idler. Reassembly was a snap till the gremlins hit again and I lost one of the drum glides. After a trip across town, I reassembled and it was good to go. Disassembly, use a screw driver to pry up the top, use the nut driver to remove upper front left and right screws, lift front forward and off bottom hooks. You have to release the wiring harness, it has four connectors. Use a sharpy marker and write the wire colors next to the plug-ins connectors you pull gently off and set the door aside. The second wires are two wires for the inner assembly which again need to be marked for color and then pulled loose. Pull them through the plastic hold down so they're out of the way. Use nut driver to remove four screws from inner drum holder, pry gently off dryer blower. Reaching around both sides of the blower housing find the belt tensioner, pull it to the right, push the belt out of it. Lift the drum out, up slightly over the back rollers. Set aside. Use the nut driver to remove the screws into the base holding the motor mount down, now lift the motor/blower assembly forward and pull gently loose from the dryer vent pipe. Set it up where you can work on it. Using the nut driver, take the screws off the blower housing, use a vise grip to secure the motor and use a 7/8 inch turning counter clockwise to remove the turbine. Use the nut driver to remove the screws holding the turbine housing in place, pop the motor clips off. Pull the motor off and remove the nut and bolt of the belt idler assembly using a wrench on the back and a socket wrench on the other side. Reverse order to reassemble, when tightening the idler arm tighten it to where you feel it stop but not any further. Put the belt around the drum again, get it in the previous location on the drum, feel around the drum to make sure belt isn't twisted, bring belt in from the back between the idler wheel and the vent pipe in a loop (Make sure the belt is behind the tension spring rather than in front), Tip the idler arm upward, use the other hand to slide the belt loop up over the motor pulley. One final note is this being a Maytag you might write these direction on the inside of the front panel for next time.