DV339AGWXAA Samsung Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from EARLYSVILLE, VA
- Parts Used:
- DC93-00634A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Dryer would not spin
The design of my dryer is a bit different from the video on PartSelect - but it is very close. And if you watch the really good video on PartSelect plus a few others on Youtube you can figure out how Samsung in general designs the different components. You can fix this yourself definitely.
Cost of part to fix - about $50.
Repairman - didn't even ask. Would probably be $300-400.
Cost of replacement $1,000.
I rated the repair "A bit difficult" only because this is the first time I have ever repaired an appliance. If I were to repair this one again, I'd rate it as Easy.
I'm really thankful for the PartSelect video. This makes DIY repairs possible.
Thanks.
Cost of part to fix - about $50.
Repairman - didn't even ask. Would probably be $300-400.
Cost of replacement $1,000.
I rated the repair "A bit difficult" only because this is the first time I have ever repaired an appliance. If I were to repair this one again, I'd rate it as Easy.
I'm really thankful for the PartSelect video. This makes DIY repairs possible.
Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from MISSOURI CITY, TX
- Parts Used:
- DC97-16782A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
noise when drying
replace Drum support roller & axel and belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from FLORAL PARK, NY
- Parts Used:
- 6602-001655
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Drier did not turn it was not the belt
I still had to take it apart there was a small sock stuck in the fan that blowes the lent out my wife left the lent filter out one time. Your video was a great help. I'm a mechanic and it was easy thanks Anthony Ratto Tulipbike82@aol.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from Frederick, MD
- Parts Used:
- DC32-00007A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dryer shut itself off and displayed error code TO
Took off the back of the dryer and replaced the thermistor. A $7 part that would have been a couple hundred dollars if we had to call a repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Corrado from YONKERS, NY
- Parts Used:
- DC93-00634A, 6602-001655
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Hooking up belt and pully
Followed video and YouTube most was easy.... put the hooking up the belt took time
Was this instruction helpful to you?
Thank you for voting!