DV203AGW (YE) Samsung Dryer - Instructions

I still had to take it apart there was a small sock stuck in the fan that blowes the lent out my wife left the lent filter out one time. Your video was a great help. I'm a mechanic and it was easy thanks Anthony Ratto [email protected]

After the Radiant Flame Sensor was installed, the problem remained. An appliance repair person then replaced both coils, and that fixed the problem.

Followed video and YouTube most was easy.... put the hooking up the belt took time

Took off the back of the dryer and replaced the thermistor. A $7 part that would have been a couple hundred dollars if we had to call a repairman.

The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.

I feel like I have a new dryer now. I replace 3 of the 4 main components using parts select. Not only did they ship next day, but the tutorial videos with Steven were right on the money and self explanative.

Since there were no troubleshooting steps, I had to start replacing the items according to the list that showed the parts that have fixed the problem for others. I ordered one at a time until I got the part that fixed the problem. I went through 4 parts before I replaced the gas solenoids which is what fixed the problem. By the time I was done, I could disassemble that dry in about 5 minutes or less.

Remove lower bottom cover (two screws on bottom) with screw driver. Remove old radiant flame sensor from left side of tube with ignior by using socket wretch. Remove wires with needle nose pliers. Put new part in: put wires back on, insert part's lower tab into the tube ( there is a small slot) use socket wrench to tighten screw at top. Put bottom front panel back on and screw back in.

unplugged dryer and removed front panel. removed the screw that holds flame sensor and unplugged electrical wires. then replaced with new. Did not solve problem so I ordered the replacement coil kit and installed them using phillips screw driver and this solved problem. Dryer is working fine now. I found this site very helpful and would recommend it to a friend.

First I replace the Radiant Flame Sensor, but the problem remain. Then replace the two coils and the igniter. Dryer works like it should. If I were to do it over, I would have replaced all 4 components to start with. Thanks for good advice and great service.

Opened the bottom panel w/ 1/4 nut driver to access the flame sensor and easy fix.

Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.

Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"

Ordered thermal fuse and cycling thermostat

On the Amana dryer, I had to remove the top panel. then the front panel to access the burner assembly. I also had to remove the gas pipe coming to the burner, because I replaced the tube burner assembly at the same time. There is only one screw that holds that back end of that gas pipe. The thermal flame sensor is on the left side of the burning chamber, with only one small Phillips head screw. just remove the 2 wires, keeping track of which terminal they belong. Just twist the sensor out of the small slot, and out it comes. The tube burner assembly is fastened with 2 screws. The entire burner assembly comes out in one piece, but be real careful not to bang the igniter when removing it. The coil assembly has 2 wires, which you cannot get wrong, because one has 2 prongs, the other has 3 wires.The local repair shop wanted 90 bucks per hour, plus parts, and I installed both the burner tube and radiant flame sensor for around $80.