7215A REV C Norge Dryer - Instructions

I followed the posted directions from others, and it was a breeze. They were really helpful. I would just add the step of keeping the drum in place with a block of wood underneath before removing the front. Slip the belt around the drum, reattach the front , and then finish positioning and tensioning the belt once the block is out of the way .

Belt was broken Removed the front (very easy) removed the drum. Noticed the roller was damaged. Replaced the roller. Installing the belt was tricky but followed an on line video. This dryer has the motor and tensioner behind the blower housing. There was not enough room to use both hands effectively. So first I placed the belt on the motor then pulled the tensioner until I could slide the belt on the tensioner with my other hand. This was the reverse order from the video. The dryer now seems to be quieter.

Unfortunately, due to a catalogue glitch, the part delivered was the wrong size. However, Donald of customer service took the time to run down the correct part, and that is enroute to me now. Donald, thank you so much for your help!

The repair was much easier than anticipated. Next time I could do it in less than 30 minuites.

Replaced the axel that holds the rollers as well as the rollers. Just rotate the left one 90 degrees and it slides out.

Probably what took the most time was puting the belt back on. It is old so I was being careful. It took a couple of trys to keep it on the rollers as I moved the drum into position. So easy I am convinced to buy another Maytag.

Wife was impressed so that's worth something!

I yanked up the front of the lid, the broken belt laid across the drum like a dead snake. Pulled that out, then removed the two screws holding the front. Using the pliers, pulled off the two wires snapped to the door switch.
Lifted out the front panel, and lifted the drum, (added a bit of a yank to get it out of the two rollers in the back).
Vacuumed out the dust and dead bugs, then tried to figure out how to thread the belt on the idler and motor. (This was the hardest part) the picture that shows the parts is an exploded view, and does not show the way that it goes together. After about half an hour, I asked for help, and we found a slight rubbing on the idler and figured out that the tensioning spring pulls on the lower part of the idler arm, not the top. Putting the belt on, and getting the spring into the hole in the base was tricky, but not hard. Reassembly was straightforward, and took less than 5 minutes. (put in the drum with the belt on it, hook the belt on the motor and idler, push the rear of the drum into the rollers, then put on the front panel, re-attach the door switch, and the two screws holding the front, and close the lid).

I googled 'replace dryer belt' and found instructions on the 'Virtual Repair Man' web site. After reading the instructions through twice I began.

First I removed lent filter and removed the two screws that hold the lent body in place. I rotated the top panel up and back and leaned it on the wall; proped up the dryer drum with some scrap wood pieces; rotated the front panel of the machine out enough to slip the new belt, groves down, around the drum; reinstalled the idler pulley under the drum; raised the drum slightly and reattached the front panel. Reattached the top panel and replaced the filter. Did a test run and worked good.

I got a price from Sears for the part and they were asking $45 just for the belt. I saved enough in parts and labor to take my wife out for a real nice dinner. thanks

I watched an online video about how to replace a dryer belt & followed the directions. Placing the belt around the drum is easy but stringing it thru the pulley is a little difficult because the belt has tension. This takes a little effort but is doable. Dryer runs great now........Be sure to unplug appliance 1st........

Worked with a guy, I'm a girl. He had a good "feeling" about how to take apart the dryer, install the belt and put it back together. After one go putting the belt on, starting the dryer and having the belt come off....I followed along silently looking at the directions. Definately needed 4 hands to put the drum back in alignment. Other than that, this was very simple PROVIDED THE DIRECTIONS TO REALIGN THE DRUM are followed at the end. So simply: my directions are meaningless here, just follow the ones enclosed with the belt and this should take no more than 1 hour. :)

Dont go in through the back!! Take the top off then the obvious steps to get to the drum and belt. On the kitchen aid model at least I would advise to make all the hassel of replacing the belt well worth your time to go ahead and buy a new tension pulley with the wheel on it as opposed to the all metal tension pulley. My dryer is much more quiet now and seems to be more efficient.

I waited a two days to get my belt then deciced to get a new tension pulley. Ordered it one day and the next it was at my door. This was well worth my time and effort. Thanks PartSelect!!

Once I realized it was just a drum belt and how easy it was to fix, I ordered the belt myself with no help from a national warehouse hardware chain where the manager said "I don't have a belt but I can sell you a dryer." Thank you I kept my 300+ dollars and once I got the belt it only required removing the two screws that sealed the lint screen cannel to the top; popping the top, removing the to nutbolts fastening the front to the side panels; slidding the front panel out; putting the belt around the drum and attaching it properly to the tension pully and motor. Finally, I closed it up and tested it. Household hero in less than 12 minutes! Not bad for a psychologist, eh?

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

Watched a video and went to town taking it apart. I stuck a pop can under the barrel to hold it up while I worked on pulleys. My dryer does not have a plastic pulley but a metal tension bar with a hole in the middle. Ran upstairs and watched a different video with my set up and all was good. 5 min of work 5 min watching Youtube and 5 min cleaning all the lint out of the machine. I am actually glad the old belt broke because some of the lint was in a clump and had scorch marks on it. I took the shop vac to every part of the cabinet and shoved it down the lint trap sleeve also.

Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.

DISCONNECT THE POWER. Double check the dryer is unplugged. Use a putty knife to free the latches holding the top of the dryer in place. Lift up the top of the dryer and secure it in place (be sure it's safely held open and won't come crashing down onto yourself as you work). Remove the two screws on the inside and near the top of the dryer, which hold the front and side panels. Gently lift up on the front panel (it may help to open the dryer door to get a better grip). Once free from the bottom clips, carefully rotate the front panel so that the door sensor wires are not strained. Once the front panel is out of the way, grab the drum and firmly lift it up and away from the back. (The drum has rollers and ridges at the rear and you'll need to pull the drum out of its "track"). Slide the new belt around the drum and position the drum about halfway inside the dryer. Loop the belt around the motor, but not the tensioner, (it will be easier to install the drum if you wait to tension the belt). With the belt around the motor, gently slide the drum back keeping the belt around the motor pulley. Press and guide the drum back onto the rollers at the rear. Check the belt is positioned correctly around the drum and motor. Reach back from the front and loop the belt around the tensioner. Rotate the drum by hand and make sure the belt is aligned and the drum spins smoothly. Position the front panel and slide it onto the lower clips. Install the screws being very careful not to drop them into the abyss... Close the lid and plug in the power.

first I took the two screws that hold the filter in, then disconected the power,then I poped the top of dryer up and removed the two 5/16 screws on the inside of the front panel then the two screws down by the loading door hinges and took off the front cover and the drum, replaced the belt and put the ajuster back on and put everything back in revers order and it is working like new thank you for the fast order .tony