DEN204A Norge Dryer - Instructions

Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. Put new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......

Others have shared as well as I can

Open the top of the dryer, thermostat can be plainly seen. this one was obviously fried, made it easy to determine cause of problem. remove old thermostat, pins pull off posts, using socket take off nuts (hang on to the nuts), put the new on. Fixed.

I loosened the belt removed the drum, removed the push nut and cracked pulley and replaced both,old push nut was a little stubborn but finally got it off.

I watched the video tape

1- cleared all the ducts. (They were clogged and this is what caused the fuse to open)
2- Replaced the fuse from the kit
3- The dryer stopped working again after 1/2 hour -the fuse blew-up again
4- Altough the stat (the other part included in the kit) checked OK with the multimeter, it was actually defective and did not regulate the temp.
5- changed both parts included in the kit, the dryer worked normally again.

This is the second time that this has happened with my dryer. The first time I replaced the thermostat and fuse, and it worked for a few years. This time I replaced the element and thermostat at first. Still nothing, then got the fuse; and walla just like new. Of course I lost a screw somewhere down at the bottom of the dryer, so there is only one holding the thermostat in place. Also I took off the front and cleaned out the lint traps; both times it was loaded with crap. Probably why it stopped in the first place.

Once we realized we needed to take the FRONT off the dryer, not the back all went well. It was an easy fix and the part fix perfectly. Instead of $60 or more for a repairman, we spent less than $20 fixing the dryer.

i followed part select instructions that probable cause was either thermal fuse or high limit thermostat.put ohm meter across both & saw thermal fuse(has pink dot on it) part 53-1182 was open.ordered thermal fuse replacement kit. part#LA-1053. the problem i had was after reaching down the side of heating housing removing the bracket with the thermal fuse,replacing & reconnecting it i had a hard time reinstalling the bracket,very tight space & i don't have very big hands.finally got the fuse in it's hole in the bracket & slid & jammed the bracket into the side of the mounting housing & it stayed secure.dryer started

Pulled the old seal off then pushed the new one in place.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

Lifted top from dryer and fuses were in the back of drum just below heating coil. Used nut driver to remove heating coil to gain access to fuses and replaced them. Process was quick and easy. Diagram from this site made locating fuses elementary!

P.S. I have no certified experience in appliance repair.This was my first time ever and dryer works perfect.

I just removed 1 screw that held the safety thermostat in and replaced it. Then I removed the long screw that holds the heating element and the high limit fuse in place. Replaced the fuse, cleaned out the lint duct area. Closed the dryer lid and pluged it in, it worked fine.

Lint filter replacement is routine maintenance. operating without a filter causes problems, a dryer sheet was sucked thru the opening and into the blower wheel, causing a lot of noise, and shaking because of the unbalance. I popped the top of the machine up, removed two screw holding the front in place, removed the front, gaining access to blower.
Removed the offending sheet, straighted the bent fin, and put everything back together again. Installeed the new filter, now it runs smooth, and quiet. mission accomplished.

I ordered this part to replace broken lint filter. Shipping estimate was 3-5 working days. I had the part 2 days after I ordered it!! I was very surprised and extremely pleased. If I need anymore appliance parts, I know exactly where to go!