DEN204KV Norge Dryer - Instructions

I googled 'replace dryer belt' and found instructions on the 'Virtual Repair Man' web site. After reading the instructions through twice I began.

First I removed lent filter and removed the two screws that hold the lent body in place. I rotated the top panel up and back and leaned it on the wall; proped up the dryer drum with some scrap wood pieces; rotated the front panel of the machine out enough to slip the new belt, groves down, around the drum; reinstalled the idler pulley under the drum; raised the drum slightly and reattached the front panel. Reattached the top panel and replaced the filter. Did a test run and worked good.

I got a price from Sears for the part and they were asking $45 just for the belt. I saved enough in parts and labor to take my wife out for a real nice dinner. thanks

With no experience repairing appliances, I did figure it out that the drive belt was broken since the motor was running and the drum did not turn.

What to do? Start looking for fasteners! I knew I had to get to the drum, but there was nothing up front, on top, or bottom that gave a clue. Only the back panel had hex head steel screws. I removed them and the panel. Then I removed a tube that pulled air from the drum to the outlet. I saw some screws holding the back of the dryer top. After removing them, the top popped off by pulling it up and releasing the attachment at the front.

This gave me access to a couple of screws holding the top of the front (holding the door). It seemed to make sense to lay what was left of the dryer on it's back. After removing the last two screws at the top corners of the front panel, I pulled it up and removed it. The drum lifted right out. The belt tightener was loose and lying against the back wall.

The local Sears did not have a replacement belt and their web site was not that helpful or forgiving. A Google search revealed a site called PartSelect. It had a very useful search routine which led me to make a purchase on a Saturday evening. The belt arrived at my door on the following Tuesday! Be sure to look at the instructions that come with the belt, it will demonstrate how to fish it through the loose belt tightener.

In about 1.5 hours the dryer was back together and doing it's thing. There were two additional screws left over, but I figure that's a manufacturing defect.

I was a hero to the wife, as usual.

First unplug the machine and turn off the gas. Then, I pried the top up (2 clamps on front, 2 screws to the lint screen). Then I removed 2 5/16 nuts that fastened front panel to sides. I held the drum and pried the front panel back while my wife slipped the new belt around the drum. Then, I buttoned everything back up in reverse order, removed the kick panel, threaded the belt through the tensioner pulley and around the motor shaft. It's really that easy. PartSelect.com makes it simple with quick, accurate service.

first I took the two screws that hold the filter in, then disconected the power,then I poped the top of dryer up and removed the two 5/16 screws on the inside of the front panel then the two screws down by the loading door hinges and took off the front cover and the drum, replaced the belt and put the ajuster back on and put everything back in revers order and it is working like new thank you for the fast order .tony

I pulled the old one off and put the new one on. It took about 3 minutes because I also replaced the old lint filter.

I tilted the unit back enough to scew the new legs into the threaded holes.

Watched the video on the site and it was spot-on! Super-easy, took like 10 minutes to replace the belt. Thanks!

Took two screws out of the Lint tray on top. remove to bolts from under hood then put new belt on. Always make sure there are no twists in belt when put back on

Disconnect power. Removed front panel and lifted top. Removed belt around spring pully and motor assembly. Carefully eased belt around back of drum and gasket. Reverse process.

Once I realized it was just a drum belt and how easy it was to fix, I ordered the belt myself with no help from a national warehouse hardware chain where the manager said "I don't have a belt but I can sell you a dryer." Thank you I kept my 300+ dollars and once I got the belt it only required removing the two screws that sealed the lint screen cannel to the top; popping the top, removing the to nutbolts fastening the front to the side panels; slidding the front panel out; putting the belt around the drum and attaching it properly to the tension pully and motor. Finally, I closed it up and tested it. Household hero in less than 12 minutes! Not bad for a psychologist, eh?

I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.

It was easy to remove the lint trap first, then the front dryer panel. The drum easily was removed and installing the new belt was a little tricky because the belt had to be mounted onto pulley while holding the drum in place. I had a little help from a friend to help me stabilize the drum as I placed the new belt. Once on, it was easy to re-install parts in reverse and have dryer working again.

Removed the two screws at the back that hold the top of the dryer. Then I pried off the top at the front by inserting a screwdriver into the front to remove the top from the clips. Then I tilted up the top like a car hood.

I removed the two screws inside that held the front on and lifted the front off. Because of the wires attached to the front, I made sure to turn the front aside without pulling on the wires. After removing the broken belt, I put the replacement belt over the front of the drum, lifting the drum a little. Then I threaded the belt over the drive and around the tension wheel per a diagram I found on the web.

While I had the front off, I removed the lint trap and cleaned out probably decades worth of lint.

Then I replaced all the parts in reverse order, plugged it in and had a working dryer!

I pried the top of the dryer with a screw driver and then lifted the top of the dryer, I then removed the two screws "with a nutdriver" that held the door in place and then removed the door and drum. I then got the new belt and placed the belt over the drum and positioned the belt through the idler arm and then on the motor pulley. I had to hold the door and drum to lock the bottom of the dryer door to the dryer and then made sure the rear drum seal was in place and the belt did not slip off the motor pulley

Ordered belt, received it two days later. It was a perfect fit.
The top of my dryer pops up from the front where 2 screws will allow the front to drop to the ground. Lift the drum slightly to get the belt on. Had to wrestle with the idler arm for about five minutes, but I won.