8741A71 Norge Dryer - Instructions

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i decided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.

Unplug dryer

Pick the top up at the front and swing up. Inside each side of the front is a screw to remove. Do not forget to unhook the door switch wires. Pull the drum. Push belt off as you remove the drum. Works better to reach in at the lower right and take the belt off of the tighener first.

After you clean out any lint in area unplug the wires from the motor and snap off the hold down clamp on the back bearing.

The blower needs to be released fromt he shaft. The snap ring in front of the blower needs to be taken off. This can be done with a screw driver by prying off the flat spot on the shaft. However, a snap ring pliers would be better. The front of the blower housing must come off as the blower must come off. There is a snap ring behind the blower that must come off also.

The biggest problem I had was removing the front motor bearing housing from the plastic blower housing. It is easy once you see that the front bearing housing is held in by four tabs in the plastic housing. By rotating the front bearing housing 90 degrees you will be able to pull it out.

From there just reverse your action. The belt went on ok. I found by putinng the belt on the drum and the motor drive pully first I was able to reach in an put the belt over the tighener.

Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

I removed the 3 screws from the front knob panel. The panel popped right off, I then removed the knob and unsrewed the two screws for the timer. You should move one wire at a time from the old timer to the new. Unfortunately, when I got finished, I had an extra white wire. That led me to virtual repairman website to get assistance with matching up the wires correctly. The virtual repairman was kind enough to provide me with a copy of the schematics for this timer. Once I received that information, I was able to get the wires lined up correctly and my dryer is like new.

Step 1. UNPLUG DRYER
Step 2. Remove the selector knob(timer). It just slides off by pulling it toward you.
Step 3. Remove the back cover of the Control Panel. Three phillips screws along the top and three 1/4" hex head screws along the back. After removing the fasteners lift up on the panel and it can be removed.
Step 4. Remove the two 1/4 hex head screws that hold the timer to the control panel. (They are on the front of the control panel under the selector knob that was removed in step 2.)
Step 4. Switch over the wires one at a time from the old timer to the new timer. Don't forget to switch over the resistor.
**Note**Also pay attention to original position on the timer, it can be installed 180deg's out(upside down) then the knob will not be indexed poperly with the control panel.
Reverse the steps to reassemble!

my ex husband took the top and front of dryer off and removed the drum and belt. he pulled off the worn roller and replaced it with the new one. we put the drum in backwards and had to turn it around but all went well and the dryer is quiet again!!!

Replaced coils on gas valve.

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.

I ordered the top 5 items that may cause this problem based on the troubleshooting guide presented by the technicians I found in youtube. I replaced the coils and that fixed the problem. The coils are the first to go out according to techs, but I have the other parts just in case I may need them later on. My Maytag dryer which is over 19 years old is alive and working again. The coils are accessible from the bottom access panel secured by 2 nut screws, unplug the dryer first, then the coils are secured by a bracket with 2 small philips head screw, I used a stubby philips screw driver to remove the bracket, undo the 2 electrical connectors on the coils one with 2 prongs and the other with 3 prongs. Put the new coils attached the electrical connectors and secured them with the bracket. Checked for any loose wiring ensuring connectors are secured in place, then test run the dryer with the panel off so you can see the if the flame stays on, if you run the dryer without wet clothes the flame may stop after 15 or so minutes. It is better to test run the dryer with wet clothes just like when your drying fresh washed and wringed clothes. It was really easy, good luck!

took 2 screws out and replace new coils

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

First I disconnected power to dryer. Next step was to lift top of cabinet and support upright. Then I removed door switch and 2 screws that hold front panel on and set front panel aside. Next was to reach under drum by belt tightener and remove drum drive belt from tightener and pulley of drive motor. Then slowly remove drum from cabinet . Once removed, I could remove old glides that were worn out and install the new ones. Before putting everything back together, I gave the cabinet a thorough vacuuming to remove all lint built up inside, checked electrical connections on heating unit and oiled back drum support rollers and belt idler roller. Next just reassembled everything in reverse order as was disassembled. Plugged cord back in and tested unit to make sure everything sounded good before drying any clothes.