7435A Norge Dryer - Instructions

Remove back panel, looking for access. upon reassembly dropped socket into lint trap. Dissemble again, also dissemble lint trap ducting, found it almost completely blocked by lint, clean and reassemble. Remove front panel and there is the problem of the broken belt. Try to look up online to no avail because I didn't have the proper machine ID, but I did find out where to look. Now with the right info ordered the part. Received in the post about 5 days. Upon reassembly I realized that the adjustor was laying in the bottom, picked up, cleaned inspected, OK, then needed to figure out where it goes, got it, then to figure out how it holds tension on belt. That took a few minutes, well maybe 10 then the old Ford light bulb came on, then installed the belt and adjuster. Replace front panel, slide back into place, hook up wiring and duct. Test, guess what folks it works.

With no experience repairing appliances, I did figure it out that the drive belt was broken since the motor was running and the drum did not turn.

What to do? Start looking for fasteners! I knew I had to get to the drum, but there was nothing up front, on top, or bottom that gave a clue. Only the back panel had hex head steel screws. I removed them and the panel. Then I removed a tube that pulled air from the drum to the outlet. I saw some screws holding the back of the dryer top. After removing them, the top popped off by pulling it up and releasing the attachment at the front.

This gave me access to a couple of screws holding the top of the front (holding the door). It seemed to make sense to lay what was left of the dryer on it's back. After removing the last two screws at the top corners of the front panel, I pulled it up and removed it. The drum lifted right out. The belt tightener was loose and lying against the back wall.

The local Sears did not have a replacement belt and their web site was not that helpful or forgiving. A Google search revealed a site called PartSelect. It had a very useful search routine which led me to make a purchase on a Saturday evening. The belt arrived at my door on the following Tuesday! Be sure to look at the instructions that come with the belt, it will demonstrate how to fish it through the loose belt tightener.

In about 1.5 hours the dryer was back together and doing it's thing. There were two additional screws left over, but I figure that's a manufacturing defect.

I was a hero to the wife, as usual.

first, i read all the comments on this web site as well as other web site. sooner i confirm the problem is the drum belt, i order the parts.
my kemore model front panel is one piece. so i have to lay down the dryer and open the front panel on the top. The instruction sheet sent with the belt is very good, so it does not take too much time to replace the belt, the challenge task is to reconnect the front panel to the side panel. I spend too much time trying different way to use the fastner hook to connect panels without realizing that the hook is broken. stupid me. i later have to use the wire to connect the front panel to side panel. overall, i am very happy i fix the dryer.

Disconnect the power and gas supply so that you can slide dryer out and into an accessable area to work comfortablely. Removed top and front of dryer. When disconnecting numerous wires from the top controls, draw a simple color coded diagram for reconnection before you disconnect those wires. After removing the top and front, take out the drum and clean all the lint, money etc. out of the normally nonexcessable area of dryer. Place new belt on as you replace the drum. This takes two people; one to hold the drum in position and one to carefully work the new belt into place. Rotating the drum by hand will assist in the placement of the new belt on the drum. After reassembling the newly cleaned dryer it was a pleasure to try it and find a dryer that worked better than during its pre-repair use and it saved us the price of a repair call or a new dryer.

Took two screws out of the Lint tray on top. remove to bolts from under hood then put new belt on. Always make sure there are no twists in belt when put back on

I pulled the old one off and put the new one on. It took about 3 minutes because I also replaced the old lint filter.

Disconnect power. Removed front panel and lifted top. Removed belt around spring pully and motor assembly. Carefully eased belt around back of drum and gasket. Reverse process.

I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.

Removed broken filter, used screwdriver to clear out some old lint in the intake and inserted new filter. New filter fits and works as described.

Buy the part the site provide a video on how to do it and was very helpful thanks

Remove broken lint filter, stick in new filter. Couldn't be easier.

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

Needed a belt. Only snag was for me was re-installing front panel (door)

Raise the top and then remove two screws to remove front. Once the front was removed on this Maytag model it was not necessary to remove the dryer drum. I simply lifted the drum slightly and slid the belt around the drum to position the belt. I then pressed the tension arm toward the drum and fed the belt around the drive pulley and tension pulley. I spun the drum a few turns by hand to insure that the belt was aligned properly. Then replaced the front cover and the top. Turned on the dryer to test and job was completed. Thanks to your video and prompt parts delivery the job was a snap. My wife didn't even have time to get mad.

I tilted the unit back enough to scew the new legs into the threaded holes.