7750A Norge Dryer - Instructions

No Repair, just replacement. Went perfect.

Using a flat-head screw driver, I removed the 1 screw from the small "door" on the back, upper right corner. Once the screw was removed, it allowed the door plate to "pop" open; exposing the old bulb. I removed the old bulb; replaced it with the new one. DONE!

Unscrewed back plate, and replaced bulb

removed screws on back plare and replaced heater element. Thank you very much foe your quick delivery of the part I ordered. I was reall;y schocked to see how fast the part arrived. I will recommend your site to anyone who needs parts like I did,.
Thany you Very Much,
Alan Brooks

Lifted hood ,and took two screws and tilted the front back and remove the door switch , and took front off ,use little socket set, took cover off fan housing took pliers removed clamp on fan , remove key way on end ,slid fan off and put new one on and reverse the way if came off.

Unplugged, loosened front cover, disconnected two wires from door open indicator, removed front cover with screw driver. Removed air flow cover with screw driver. Used pliers and retaining ring pliers to remove old blower wheel, my husband calls it a "squirrel cage". Installed new blower wheel and reassembled. It was all easy to see and get to. Thanks for having the right part. Sue.

First I disconnected power to dryer. Next step was to lift top of cabinet and support upright. Then I removed door switch and 2 screws that hold front panel on and set front panel aside. Next was to reach under drum by belt tightener and remove drum drive belt from tightener and pulley of drive motor. Then slowly remove drum from cabinet . Once removed, I could remove old glides that were worn out and install the new ones. Before putting everything back together, I gave the cabinet a thorough vacuuming to remove all lint built up inside, checked electrical connections on heating unit and oiled back drum support rollers and belt idler roller. Next just reassembled everything in reverse order as was disassembled. Plugged cord back in and tested unit to make sure everything sounded good before drying any clothes.

I opted to remove front, top and back panels. This is best done with dryer laying on it's back so drum remains in position. Hold panels and pieces in place with masking tape (2") You should block up the dryer so you don't damage the gas pipe. I opted to total shop vac out the piece and lubricate the rollers and tension pulley. I made more in change than the belt cost!

Overall an easy repair. Belt came with diagram for easy threading the belt.

Finally got tired to greasing the wheels only to have to do it again so I sprung for new wheels and shafts. Popped the top open, removed the drum, installed the two new shafts with supplied screws then attached the wheels. Figured I'd change out the original belt while I was at it even though the old one still looked good. It's nice and quiet again, plus it give me a chance to clean it out.

googled"dryer not heating". landed on partsselect.com. checked parts like website said with multimeter. pointed to thermostat. ordered it, replaced it, it works now.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

Took the front of dryer apart removed belt and drum replaced my parts and reassembled.

Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.

My part came a day or so after the order was placed. There was really no installation required, but I will definitly make orders from this site again. Thank you very much!

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve