7761A-71 Norge Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Martin from Grapevine, TX
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door catch broken
Push new catch in the opening, close the door and VOILA! the door stays closed. Please note that the cost of this part is exorbitant- it's worth about 50 cents but with shipping it cost about $11.00. Check your local hardware store first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from North Myrtle Beach, SC
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Male door latch would no longer catch.
After ordering the part, I read the information left by other users. I used a screw driver to pop out the piece, and then put the new latch in the opening. A gentle pop with the side of my hand, and the door latch went right into place. Who knew there was a second door latch on the other side that could've been used?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from Cary, NC
- Parts Used:
- LA-1008
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers
Squealing noise
Followed directions on movie. This was a simple process. Although in the end I found that replacing the rollers was not the problem in the end. It turned out to be the motor, which I was able to repair with some prior experience with electric motors and a bit of oil. That's why it took as long as it did to make the total repair. Still happy with the outcome.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from Indianapolis, IN
- Parts Used:
- WP53-0918
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench set
Broken lint filter
Replacing the lint filter was, of course, the easy part. The rest of the time was spent removing the front of the dryer and cleaning out all the lint that had escaped through the old broken filter. I completely took apart the lint traps inside the front, vacuumed everything out, and replaced the ductwork to the outside that was almost completely blocked with lint. Please take the time to inspect your dryer, and do this if necessary! I feel we prevented a house fire by getting to this in time - and I will be more vigilant in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Oakland, CA
- Parts Used:
- WP53-0918
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lint filter screen was starting to deteriorate
took out the old, put in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leona from Colorado Springs, CO
- Parts Used:
- LA-1008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Noise in dryer when first starting up
Turn off power. Move dryer away from wall and release the top by lifting up to release the two clips. Lay top against the wall. Remove the two screws, one in each corner, left and right inside the cabinet. Lift front panel up and out away from dryer. Place along right side of dryer. You may need to unlatch the wiring for the door switch. Reach inside the bottom of dryer and release the belt. Lift the dryer drum out along with the belt. Observe the two guide rollers that the drum rides on. Using a blade screw driver release the clips that hold the rollers onto the spindles. Clean up around each spindle. Install new rollers in reverse order and put all back together. The hardest part is reinstalling the belt. Put belt around the drum, around the motor pulley and then onto the tension roller. Good luck..
Was this instruction helpful to you?
Thank you for voting!