8215A (REV E) Norge Dryer - Instructions

Had a problem holding drum in place and putting front back on. Got it together and drum wouldn't turn. Had to tear it a part again and belt had turned.

It was easy. Just removed the old seal and plugged the new one in place. Took less than 3 minutes

After reading everyone else's comments I started by pulling out the dryer, unplugging the power and exhaust. Next moved the dryer to an area where I had room to lay it on the back. Then using a flat blade screw driver, I popped the top attached tape to the top so I could lean back the top without having to hold it. Removed the two screws from the front panel and removed the door safety shut off before removed the front panel. Then I layed the dryer on its back. Then reached under the drum, pushed the belt tensioner toward the motor puller to release the tension on the belt. Then slid the belt to the base. Pulled the drum up and out of the cabinet. Next I cleaned all the lint and crud out of the dryer components. To remove the clips that hold the rollers in place, I use 2 small flat blade screw drivers. These are inserted at the back side of the horse show shaped clip between the shaft and the clip. When the two screw drivers are rotated like turning a screw they slide the clip out. Next I used a socket wrench with a #8 metric socket(I didn't have the sae size) and removed the screws holding the drum roller brackets. I simply reversed the procedure to install the new rollers. Since the dryer was on its back, when I put the drum back in, its own weight slipped it in place. Then pulled the belt around the drum and between the motor pulley and the belt tensioner. Holding the belt with one hand, I used the other hand to pushed the belt tensioner in and positioned the belt. Then I stood the unit back upright and put the front cover on, replaced the door safety switch, removing the tape holding the lid and then cloed the lid. Of course I put the dryer back in place, leveled it, and it now runs like brand new. My thanks to every one else who gave me hints that saved be about $450!

Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. Put new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......

Checked out the coil seemed ok. So I replaced the radiant flame sensor. No change. Then I replaced the High limit sensor still the heat was not staying on. I read some were in the troubleshooting guide that the coil can test good, but can still malfunction. So that was it new coil fix it, works like a new Dryer again.

Received the replacement filter which was an exact duplicate of the 22 year old filter. Took the old one out; slid the new one in and got ready for another 22 years of use. At 86 years of age I probably won't be around to see the new filter wear out. The dryer has already outlasted the place where I purchased it - Montgomery Wards! They just don't make stuff to last like this anymore.

First I removed the screws of the dryer cover. Next removed the screws holding the dryer drum.

Drilled out the two rivets left from the old glide. Inserted the plastic and postitioned the cushion underneath. Inserted the new glide and drilled a hole in the plastic to accomodate the new rivet. Inserted rivet. Pulled the other end so it was tight holding the cushion and did the other end. Done.

Had to cut the glide 1/4 '' of the width to slide it through the existing slots in the panel.

I just followed your video how to replace a broken belt , after viewing replacing belt went easy

the video was very well done and able to understand. disconnect power ,remove lint trap,remove 2 phillps head screws, push putty knife in front seam line about 1'' in from corners to release top assembly ,lift up and support, disconnect wire connector ,remove 1 screw in each front corner lift front panel off while holding drum, remove broken belt,install new belt with grooves against drum ,feed around tensioner pulley and onto motor shaft pulley ,spin drum by hand to make sure belt tracking etc. reassembly in reverse.

I opened up the dryer lifting the lid with a putty knife and removed the two screws holding the front. I reached in and removed the belt and removed the drum. I took my shop vac and cleaned all the lint, the door passage to the lint screen extremly full of hard lint. I tested the coils with my multi meter and they tested bad. I also did the test that was suggested by Part Select and again it showed the coils as bad. Once I received the parts about three days, it only took about twenty minutes to install using just a screw driver to replace the coils and the belt went on real easy with easy access to the tentioner. and my dryer now runs more quiet and dries the clothes in half the time it used to take. My belt was still in pretty good shape but I put a new one on since I had it apart any way. My friend had the same problem with his dryer and spent $300.00 for a repairman to do the same thing. I tried to tell him it is not rocket science and very easy to do yourself. Thank you Part Select for the good repair advice as well as the timely delivery of the parts.

Vacuum out the dryer vent & trap of all the tenant's sleeping bag stuffing, intall the new lint trap and Voila! It works again.

I took apart the dryer by unscrewing the top and the front, front comes off by just undoing the two top screws on the inside. I figured it was something to do with the rollers since the noise was ciclycal. The hardest part was to put the drive belt back on. It helps to have a second person for about 5 minutes.

I ordered this part to replace broken lint filter. Shipping estimate was 3-5 working days. I had the part 2 days after I ordered it!! I was very surprised and extremely pleased. If I need anymore appliance parts, I know exactly where to go!

Lint filter replacement is routine maintenance. operating without a filter causes problems, a dryer sheet was sucked thru the opening and into the blower wheel, causing a lot of noise, and shaking because of the unbalance. I popped the top of the machine up, removed two screw holding the front in place, removed the front, gaining access to blower.
Removed the offending sheet, straighted the bent fin, and put everything back together again. Installeed the new filter, now it runs smooth, and quiet. mission accomplished.

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done